manualshive.com logo in svg

Rosslare AYC-E 5 Series, Installation And Programming Manual

Share
Download
Rosslare AYC-E 5 Series Installation And Programming Manual Download Page 19

Reader Operation 

AYC-Ex5/T65 Series Installation and Programming Manual 

19 

3.2.3

 

Selecting Keypad Transmission Format 

There are seven keypad transmission formats. 
More information on each of the keypad transmission formats is 

presented in Section 

 

3.2.3.1. 

 

Only one keypad transmission format can be active at any one time. 

To select the keypad transmission format: 

1.

 

Enter Programming mode. 

 

2.

 

Press 

1

 to enter Menu 1. 

 

The left LED turns red. 

 

3.

 

Enter one of the following options: 

1

 – Single Key, Wiegand 6-Bit (Rosslare Format) (default) 

2

 – Single Key, Wiegand 6-Bit with  Parity Bits 

3

 – Single Key, Wiegand 8-Bit, Nibbles Complemented 

4

 – 4 Keys  Facility Code, Wiegand 26-Bit 

5

 – 1 to 5 Keys + Facility Code, Wiegand 26-Bit 

6

 – 6 Keys BCD and Parity Bits, Wiegand 26-Bit 

8

 – 1 to 8 Keys BCD, Clock & Data Single Key 

 

When selecting Option 8, the right LED turns orange and an 

additional input is required to specify the number of keys in 

the PIN code. 

 

You hear three beeps. 
The system returns to Standby mode. 

 

Green 

Red  Green 

Red 

Summary of Contents for AYC-E 5 Series


































































Reviews:

No comments

Brands by name

Popular brands

Load more brands