106
7. What to Do If...
7-2 Responding to a Message
[CAN'T PRINT CROP CONTINUE?]
The size of the data including the crop marks is larger than
the printing area of the loaded media.
To continue performing output without correcting this, press the
[ENTER] key. At this time, the portion extending beyond the print-
ing or cutting area and crop marks is not output. To stop output,
stop sending data from the computer, then raise the sheet loading
lever. Make the printing or cutting area wider such as by replacing
the media with a larger piece of media or by changing the posi-
tions of the pinch rollers, then send the data again.
The size of the data being output is too small.
Make the size of the data of the scan direction at least 65 mm (2-
9/16 in.). To continue performing output without correcting this,
press the [ENTER] key. At this time, the data is output without
printing the crop marks. To stop output, stop sending data from
the computer, then raise the sheet loading lever. Change the size
of the data, then send the data again.
The size of the data of the feed direction is not limited.
[CROPMARK ERROR NOT FOUND]
Automatic detection of crop marks could not be accom-
plished.
Load the media at the correct position and perform detection of
crop marks again. Depending on the media, it may not be possible
to detect crop marks automatically. If repeating automatic crop-
mark detection results in an error again, then perform manual crop-
mark detection.
[CANCELED FOR PROTECTING MOTOR]
Continuous operation caused the pump motor to become
hot, so operation was paused.
Press any key to cancel the error. Allow the unit to stand for about
40 minutes, then resume operation.
[CHECK HEATER VOLTAGE SETTING]
The heaters didn't reach their preset temperatures although
approximately 20 minutes had passed since printing started.
Raise the temperature of the room if it is low.
When this message appears in spite of using the machine in the
recommended environment (refer to "8-1 Specifications"), check
if the voltage switches match the voltage of the region where the
machine is used.
To continue waiting for reaching the preset temperature, press the
[ENTER] key.
To start printing although the heaters have not reached their preset
temperature, press the [PAUSE] key.
[MOTOR ERROR TURN OFF POWER]
A motor error occurred.
Operation cannot be continued. [Use the [POWER] key to switch
the power off and back on again. After rectifying the cause of the
error (a media jam or the like), switch on the power. Never leave
the unit with the printing carriage not in standby position.
[TEMPERATURE IS TOO LOW]
The air temperature where installed is lower than the mini-
mum ambient temperature at which the unit can operate
(approx. 5ºC[41ºF]).
Operation cannot be continued. Use the [POWER] key to switch
the power off. First raise the temperature of the area where in-
stalled, then switch on the power.
[TEMPERATURE IS TOO HIGH]
The air temperature where installed is higher than the maxi-
mum ambient temperature at which the unit can operate
(approx. 40ºC [104ºF]).
Operation cannot be continued. Use the [POWER] key to switch
the power off. First lower the temperature of the area (15 to 35ºC
[59 to 95ºF] where installed, then switch on the power.
[HEATER VOLTAGE SETTING ERROR]
The heater temperature experienced a sudden rise because
the settings for the voltage switches are incorrect.
Operation cannot be continued. Press the [POWER] key to switch
off the power, then switch off the main power switch. Next, go to
"1-3 Assembling and Installing" and refer to "Step 5: Set the Volt-
age Switches," and make the correct settings for the voltage
switches. Finally, switch on the main power switch, then switch
on the sub power.
[AVOIDING DRY-UP TURN OFF POWER]
Forced movement to the standby position was performed in
order to prevent the heads from drying out.
Operation cannot be continued. Press the [POWER] key to switch
the power off and back on again. Opening the front cover while
printing is in progress causes an emergency stop, and when the
machine is left in this state for ten minutes or more, forced retrac-
tion of the printing heads is performed.
[CARRIAGES ARE SEPARATED]
The cutting carriage and the printing carriage were improp-
erly disconnected.
A problem such as a media jam occurred, impeding correct opera-
tion. Operation cannot be continued. Press the [POWER] key to
switch the power off and back on again.
[SERVICE CALL No: * * * *]
An unrecoverable error occurred, or part replacement that
must be performed by a service technician is required.
Check the number shown on the display, then press the [POWER]
key to switch off the power. After you switch off the power, in-
form your authorized Roland DG Corp. dealer or service center of
the number that appeared on the display.
Summary of Contents for SP-300
