You can adjust the Chorus send level of specified channel.
This message is ignored when “Receive control change” of the system common is OFF.
• NRPN MSB/LSB
Status
Second
Third
BnH
63H
mmH
BnH
62H
llH
n = MIDI channel number: 0H — FH (ch.1 — ch.16)
mm = MSB of the specified parameter by NRPN
ll = LSB of the specified parameter by NRPN
When the power is turned on, or “General MIDI System On” is received, Rx.NRPN will be set OFF, and NRPN will not
be received.
When “GS reset” or Rx.NRPN = ON is received,NRPN can be received.
The value set by NRPN will not be reset even if Program change or Reset all controller is received.
** NRPN **
The NRPN (Non Registered Parameter number) message allows an extended range of control changes to be used, let-
ting you use control messages which are not part of the MIDI Specification and may be unique to an individual
model. To use these messages, you must first use NRPN MSB and NRPN LSB message to specify the parameter to be
controlled, and then use Data Entry messages to specify the value of the specified parameter. Once an NRPN para-
meter has been specified, all Data Entry messages received on that channel will modify the value of that parameter.
To prevent accidents, it is recommended that you set RPN Null (RPN Number = 7FH/7FH) when you have finished
setting the value of the desired parameter.
On This module, the following NRPN can be received.
NRPN
Data entry
MSB LSB
MSB
Function and range
01H 08H
mmH
Vibrato Rate (relative change)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
01H 09H
mmH
Vibrato Depth (relative change)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
01H 0AH
mmH
Vibrato Delay (relative change)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
01H 20H
mmH
TVF Cutoff Frequency (relative change)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
01H 21H
mmH
TVF Resonance (relative chenge)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
01H 63H
mmH
TVF&TVA Envelope Attack Time (relative change)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
01H 64H
mmH
TVF&TVA Envelope Decay Time (relative change)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
01H 66H
mmH
TVF&TVA Envelope release Time (relative change)
mm: 0EH — 40H — 72H (–50 — 0 — +50)
18H rrH
mmH
Rhythm Instrument Pitch Coarse (relative change)
rr: Rhythm Instrument note number
mm: 00H — 40H — 7FH (–64 — 0 — +63 semitone)
1AH rrH
mmH
Rhythm Instrument TVA level (absolute change)
rr: Rhythm Instrument note number
mm: 00H — 7FH (0 — max)
1CH rrH
mmH
Rhythm Instrument Panpot (absolute change)
rr: Rhythm Instrument note number
mm: 00H, 01H — 40H — 7FH (random, left-center-right)
1DH rrH
mmH
Rhythm instrument Reverb Send Level (absolute change)
rr: Rhythm Instrument note number
mm: 00H — 7FH (0 — max)
1EH rrH
mmH
Rhythm Instrument Chorus Send Level (absolute change)
rr: Rhythm Instrument note number
mm: 00H — 7FH (0 — max)
Data entry LSB (llH) is ignored
Parameters marked “relative change” change relative to the preset value (40H). Even among different GS devices,
“relative change” parameters may sometimes differ in the way the sound changes or in the range of change.
Parameters marked “absolute change” will be set to the absolute value of the parameter, regardless of the preset
value.
• RPN MSB/LSB
Status
Second
Third
BnH
65H
mmH
BnH
64H
llH
n = MIDI channel number: 0H — FH (ch.1 — ch.16)
mm = MSB of the specified parameter by RPN
ll = LSB of the specified parameter by RPN
** RPN **
RPN (registered parameter number) is a parameter number of tone color or musical expression defined in MIDI spec-
ification.
With the Sound Expansion Series as the receiver,RPN#0 (pitch bend sensitivity), RPN#1 (fine tuning) and RPN#2
(coarse tuning) are effective. when sending an RPN to the Sound Expansion Series,first specify the MSB and LSB of
the RPN to be used to control a parameter and then set the value in the data entry field.
RPN
Data entry
Description
MSB LSB
MSB LSB
00H 00H
mmH —
Pitch bend sensitivity
mm: 00H — 0CH (0 — 12 semitone)
ll: Ignored
Up to 1 octave
You can adjust “BENDER — RANGE DOWN” and “BENDER — RANGE UP” at same
time.
In the rhythm part (part8), this message is not recognized.
00H 01H
mmH llH
Fine tuning
mm, ll: 20H, 00H — 40H, 00H — 60H, 00H
(–8192 x 50 / 8192 — 0 — +8192 x 50 / 8192 cent)
In the patch mode, the master tune is adjusted.
In the performance mode, fine tune at each part is adjusted.
In the performance mode, when received as specified control channel, the master
tune is adjusted.
00H 02H
mmH —
Coarse tuning
mm: 10H — 40H — 70H (–48 — 0 — +48 semitone)
ll: Ignored
In the patch mode, this message is not recognized.
In the performance mode, coarse tune for each part is adjusted .
7FH 7FH
— —
RPN reset
mm, ll: Ignored
It returns to the state where no RPN parameters are specified. Current setting value is
no change.
• Data entry MSB/LSB
Status
Second
Third
BnH
06H
mmH
BnH
26H
llH
n = MIDI channel number: 0H — FH (ch.1 — ch.16)
mm = MSB of the value of the parameter specified with RPN
ll = LSB of the value of the parameter specified with RPN
This message is ignored when “Receive control change” of the system common is OFF.
• Program Change
Status
Second
CnH
ppH
n = MIDI channel number: 0H — FH (ch.1 — ch.16)
pp = Program number: 00H — 7FH (prog.1 — prog.128)
This message is ignored when “Receive program change” of the system common is OFF.
If the part which MIDI receive channel is set the same as the control channel, the performance is changed when
receive the program change message.
• Channel pressure
Status
Second
DnH
vvH
n = MIDI channel number: 0H — FH (ch.1 — ch.16)
vv = value: 00H — 7FH (0 — 127)
The effect of the Channel pressure depends on the value of “After 1 — 4” of the patch tone.
This message is ignored when “Receive Channel pressure” of the System common is OFF.
• Pitch bend change
Status
Second
Third
EnH
llH
mmH
n = MIDI channel number: 0H — FH (ch.1 — ch.16)
mm, ll = value: 00H, 00H — 7FH, 7FH (–8192 — +8191)
This message is ignored when “ Receive Pitch bend “ of the system common is OFF.
13
MIDI IMPLEMENTATION
