manualshive.com logo in svg

ROJ SUPER ELF X3, Operating Instructions Manual

Introducing the ROJ SUPER ELF X3! Enhance your adventures with this exceptional device. Stay on top of its advanced features by referring to our comprehensive Operating Instructions Manual. Experience hassle-free access as you effortlessly download this manual for free, exclusively from manualshive.com. Maximize the potential of your ROJ SUPER ELF X3 today!

Share
Download
background image

SUPER ELF X3

– Dornier

5

2. SETTING AND CONTROL ELEMENTS

Front Control elements

1

FUNCTION BUTTON

It activates the Electromagnet and allows the following operations:

a-

Weft reserve removal.

b-

New weft reserve loading.

c-

Release of only one coil when the weft reserve is already on the Spool Body.

d-

Photocells calibration

e-

Reset of the fatal errors without switching OFF the main power.

A

SIGNALING LED

When the weft feeder is powered, the led turns on if no faults are detected. In case of
problems, the led blinks. Slow blinking in case of warnings, fast blinking in case of fatal errors.

B

ADJUSTMENT SCREWS FOR THE ELECTROMAGNET
POSITION

C, D, E

ADJUSTMENTS SCREWS OF SPOOL BODY DIAMETER

(Coil length)

F

PUSH BUTTON FOR SETTING OF WINDING DISC ROTATION
DIRECTION AND COILS SEPARATION

Summary of Contents for SUPER ELF X3

























Reviews:

No comments

Related manuals for SUPER ELF X3

Brands by name

Popular brands

Load more brands