ROJ SUPER ELF X3 Operating Instructions Manual Download Page 2 | Manualshive

Page: 2 / 24

background image

WARNING!

- Condensation could form on the Weft Feeder when it is moved from the cold environment of
the warehouse to the warmer environment of the weaving room. Make sure that it is
completely dry before connecting to power.

- Provide proper information to the people operating the weft Feeders.

- The installation, connection, adjustment, and maintenance of the Weft Feeder has to be
performed by technically qualified personnel.

- The Loom's main power switch MUST be switched OFF before any replacing or connecting
operation.

- Caution must be taken on the close vicinity of the Feeder. In normal working condition, it can
start running without prior warning and the moving parts might cause injuries.

- Repairing any electrical part of the unit has to be carried out by Roj s.r.l.
authorized personnel.

-Always use proper spare parts and accessories supplied by Roj s.r.l.

- Roj s.r.l. disclaims all responsibility for the improper use of the Feeder different from what
described in the chapter 1. General Information.

«
1
2
3
4
...
»

Summary of Contents for SUPER ELF X3

























Reviews:

No comments

Related manuals for SUPER ELF X3

WOLF PUP 8.10 STROLLER

Brand: Schacht Pages: 4

Brand: Schacht Pages: 8

MIGHTY WOLF FL3002E

Brand: Schacht Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands