manualshive.com logo in svg

Rockwell RCV144ACx, Command Reference Manual

The Rockwell RCV144ACx is a high-quality networking product designed to enhance communication efficiency. For detailed instructions on how to maximize its potential, download the Command Reference Manual for free from manualshive.com. This manual provides step-by-step guidance on configuration and troubleshooting, ensuring seamless operation.

Share
Download
background image

AT Command Reference Manual

viii

1048

CONNECT 26400 (63)........................................................................................................................ 3-45
CONNECT 28800 (64)........................................................................................................................ 3-46
COMPRESSION: CLASS 5 (66) ......................................................................................................... 3-46
COMPRESSION: V.42 bis (67) ........................................................................................................... 3-46
COMPRESSION: NONE (69) ............................................................................................................. 3-46
PROTOCOL: NONE (70) .................................................................................................................... 3-46
PROTOCOL: LAPM (77) .................................................................................................................... 3-46
CARRIER 31200 (78) ......................................................................................................................... 3-46
CARRIER 33600 (79) ......................................................................................................................... 3-46
PROTOCOL: ALT (80)........................................................................................................................ 3-46
PROTOCOL: ALT-CELLULAR (81)..................................................................................................... 3-46
CONNECT 33600 (84)........................................................................................................................ 3-46
CONNECT 31200 (91)........................................................................................................................ 3-46
CARRIER 32000 (150) ....................................................................................................................... 3-46
CARRIER 34000 (151) ....................................................................................................................... 3-46
CARRIER 36000 (152) ....................................................................................................................... 3-47
CARRIER 38000 (153) ....................................................................................................................... 3-47
CARRIER 40000 (154) ....................................................................................................................... 3-47
CARRIER 42000 (155) ....................................................................................................................... 3-47
CARRIER 44000 (156) ....................................................................................................................... 3-47
CARRIER 46000 (157) ....................................................................................................................... 3-47
CARRIER 48000 (158) ....................................................................................................................... 3-47
CARRIER 50000 (159) ....................................................................................................................... 3-47
CARRIER 52000 (160) ....................................................................................................................... 3-47
CARRIER 54000 (161) ....................................................................................................................... 3-47
CARRIER 56000 (162) ....................................................................................................................... 3-47
CONNECT 32000 (165)...................................................................................................................... 3-47
CONNECT 34000 (166)...................................................................................................................... 3-47
CONNECT 36000 (167)...................................................................................................................... 3-47
CONNECT 38000 (168)...................................................................................................................... 3-48
CONNECT 40000 (169)...................................................................................................................... 3-48
CONNECT 42000 (170)...................................................................................................................... 3-48
CONNECT 44000 (171)...................................................................................................................... 3-48
CONNECT 46000 (172)...................................................................................................................... 3-48
CONNECT 48000 (173)...................................................................................................................... 3-48
CONNECT 50000 (174)...................................................................................................................... 3-48
CONNECT 52000 (175)...................................................................................................................... 3-48
CONNECT 54000 (176)...................................................................................................................... 3-48
CONNECT 56000 (177)...................................................................................................................... 3-48
CONNECT 230400 (20)...................................................................................................................... 3-48
+FCERROR (+F4) ..............................................................................................................................3-48

3.9 AUDIOSPAN AND DSVD COMMANDS .............................................................................................................. 3-49

3.9.1 Commands Supported by Both AudioSpan and DSVD ........................................................................... 3-49

-SMS= x, y, z, t - Select AudioSpan/DSVD Mode ................................................................................3- 49
#VLS = x - Voice Line Select............................................................................................................... 3-50

3.9.2 Commands Supported Only by DSVD.................................................................................................... 3-50

-SSE= x - Enable/Disable DSVD ......................................................................................................... 3-50

3.9.3 Commands Supported Only by AudioSpan ............................................................................................ 3-51

-SQS= x, y - Select AudioSpan Modulation ......................................................................................... 3-51

3.9.4 Examples .............................................................................................................................................. 3-53

3.10 SYNCHRONOUS ACCESS MODE ................................................................................................................... 3-58

3.10.1 Synchronous Access Mode Commands ............................................................................................... 3-58

+ES - Enable Synchronous Access Mode ........................................................................................... 3-58
+ESA - Configure Synchronous Access Submode............................................................................... 3-59
+ ITF - Transmit Flow Control Thresholds ........................................................................................... 3-61

4. S-REGISTERS ..............................................................................................................................................................4-1

4.1 FACTORY DEFAULTS .........................................................................................................................................4-1

4.2 S-REGISTER DEFINITIONS.................................................................................................................................4-4

Summary of Contents for RCV144ACx



























































































































































































Reviews:

No comments

Related manuals for RCV144ACx

OUMAN 3G-MOD5 Quick Start Manual preview
3G-MOD5
Brand: OUMAN Pages: 6
Patton electronics NetLink 1095 User Manual preview
NetLink 1095
Brand: Patton electronics Pages: 20
Patton electronics NetLink 1094A User Manual preview
NetLink 1094A
Brand: Patton electronics Pages: 17
Motorola MB7420 Quick Start Manual preview
MB7420
Brand: Motorola Pages: 12
OUMAN 4G-MOD1 Manual preview
4G-MOD1
Brand: OUMAN Pages: 6
MultiModem MT5634ZPX-PCI Owner'S Manual preview
MT5634ZPX-PCI
Brand: MultiModem Pages: 88
Hama FlashPen My Disa USB Data Safe Operating Instruction preview
FlashPen My Disa USB Data Safe
Brand: Hama Pages: 14
Paradyne 3825-A2-GX40-00 Safety Notes preview
3825-A2-GX40-00
Brand: Paradyne Pages: 1
Four-Faith F-B200GLGL Hardware Design Manual preview
F-B200GLGL
Brand: Four-Faith Pages: 34
TECOM WM5030-OD Mounting Manual preview
WM5030-OD
Brand: TECOM Pages: 17
RCA DCM425 Owner'S Manual preview
DCM425
Brand: RCA Pages: 35
NETGEAR DM200 User Manual preview
DM200
Brand: NETGEAR Pages: 107
HORNER HE-XRZ2 Quick Start Manual preview
HE-XRZ2
Brand: HORNER Pages: 11
Sitecom DC-206 Manual preview
DC-206
Brand: Sitecom Pages: 14
D-Link DSL-300G+ Technical Bulletin preview
DSL-300G+
Brand: D-Link Pages: 11
Orcon DM11Pv2 Installation Manual preview
DM11Pv2
Brand: Orcon Pages: 2
Hamlet HNWU300NN User Manual preview
HNWU300NN
Brand: Hamlet Pages: 34
Paradyne COMSPHERE 3911 Installation And Operation Manual preview
COMSPHERE 3911
Brand: Paradyne Pages: 280

Brands by name

Popular brands

Load more brands