Rockwell RCV144ACx Command Reference Manual Download Page 63 | Manualshive

Page: 63 / 186

Rockwell RCV144ACx Command Reference Manual Download Page 63

AT Command Reference Manual

1048

3-45

CARRIER 7200 (49)

The modem sends this result code when a 7200 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 9600 (50)

The modem sends this result code when a 9600 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 12000 (51)

The modem sends this result code when a 12000 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 14400 (52)

The modem sends this result code when a 14400 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 16800 (53)

The modem sends this result code when a 16800 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 19200 (54)

The modem sends this result code when a 19200 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 21600 (55)

The modem sends this result code when a 21600 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 24000 (56)

The modem sends this result code when a 24000 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 26400 (57)

The modem sends this result code when a 26400 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CARRIER 28800 (58)

The modem sends this result code when a 28800 bps data rate has been detected on the line and carrier reporting has been
enabled. (See S95 and Xn.)

CONNECT 16800 (59)

For X1, X2, X3, and X4, the modem returns this result code upon connecting when the DTE speed is 16800 bps and the
modem has been instructed to report the DTE speed upon connecting.

CONNECT 21600 (61)

For X1, X2, X3, and X4, the modem returns this result code upon connecting when the DTE speed is 21600 bps and the
modem has been instructed to report the DTE speed upon connecting.

CONNECT 24000 (62)

For X1, X2, X3, and X4, the modem returns this result code upon connecting when the DTE speed is 24000 bps and the
modem has been instructed to report the DTE speed upon connecting.

CONNECT 26400 (63)

For X1, X2, X3, and X4, the modem returns this result code upon connecting when the DTE speed is 26400 bps and the
modem has been instructed to report the DTE speed upon connecting.

«
...
61
62
63
64
65
...
»

Summary of Contents for RCV144ACx



























































































































































































Reviews:

No comments