manualshive.com logo in svg

Rockwell RCV144ACx, Command Reference Manual, Page: 7 / 186

Share
Download
Rockwell RCV144ACx Command Reference Manual Download Page 7

AT Command Reference Manual

1048

vii

Example of Formatted Form Reporting ............................................................................................ ...3-37
Unformatted Form Reporting .............................................................................................................. 3-37
Example of Unformatted Form Reporting .......................................................................................... ..3-37

3.7 CELLULAR COMMANDS....................................................................................................................................3-38

3.7.1 Cellular Phone Drivers ........................................................................................................................... 3-38

3.7.2 Cellular Commands ............................................................................................................................... 3-38

^C2 - Download Cellular Phone Driver ................................................................................................ 3-38
^I - Identify Cellular Phone Driver............................................................................................ ............ 3-38
^T6 - Indicate Status of Cellular Phone ............................................................................................... 3-39

3.7.3 Operation .............................................................................................................................................. 3-39

Modem Configuration ......................................................................................................................... 3-39
Fax Configuration ............................................................................................................................... 3-40
Cellular Phone Configuration .............................................................................................................. 3-40

3.8 AT COMMAND RESULT CODES ....................................................................................................................... 3-42

OK (0) 3-42
CONNECT (1) ....................................................................................................................................3-42
RING (2) ....................................................................................................................... ..................... 3-42
NO CARRIER (3)................................................................................................................................3-42
ERROR (4)......................................................................................................................................... 3-42
CONNECT 1200 (5)............................................................................................................................3-42
NO DIALTONE (6).............................................................................................................................. 3-42
BUSY (7)............................................................................................................................................ 3-43
NO ANSWER (8) ................................................................................................................................3-43
CONNECT 0600 (9)............................................................................................................................3-43
CONNECT 2400 (10).......................................................................................................................... 3-43
CONNECT 4800 (11).......................................................................................................................... 3-43
CONNECT 9600 (12).......................................................................................................................... 3-43
CONNECT 7200 (13).......................................................................................................................... 3-43
CONNECT 12000 (14)........................................................................................................................ 3-43
CONNECT 14400 (15)........................................................................................................................ 3-43
CONNECT 19200 (16)........................................................................................................................ 3-43
CONNECT 38400 (17)........................................................................................................................ 3-44
CONNECT 57600 (18)........................................................................................................................ 3-44
CONNECT 115200 (19)...................................................................................................................... 3-44
CONNECT 75TX/1200RX (22)............................................................................................................ 3-44
CONNECT 1200TX/75RX (23)............................................................................................................ 3-44
DELAYED (24) ...................................................................................................................................3-44
BLACKLISTED (32) ............................................................................................................................3-44
FAX (33)............................................................................................................................................. 3-44
DATA (35) .......................................................................................................................................... 3-44
CARRIER 300 (40) .............................................................................................................................3-44
CARRIER 1200/75 (44) ...................................................................................................................... 3-44
CARRIER 75/1200 (45) ...................................................................................................................... 3-44
CARRIER 1200 (46) ........................................................................................................................... 3-44
CARRIER 2400 (47) ........................................................................................................................... 3-44
CARRIER 4800 (48) ........................................................................................................................... 3-44
CARRIER 7200 (49) ........................................................................................................................... 3-45
CARRIER 9600 (50) ........................................................................................................................... 3-45
CARRIER 12000 (51) ......................................................................................................................... 3-45
CARRIER 14400 (52) ......................................................................................................................... 3-45
CARRIER 16800 (53) ......................................................................................................................... 3-45
CARRIER 19200 (54) ......................................................................................................................... 3-45
CARRIER 21600 (55) ......................................................................................................................... 3-45
CARRIER 24000 (56) ......................................................................................................................... 3-45
CARRIER 26400 (57) ......................................................................................................................... 3-45
CARRIER 28800 (58) ......................................................................................................................... 3-45
CONNECT 16800 (59)........................................................................................................................ 3-45
CONNECT 21600 (61)........................................................................................................................ 3-45
CONNECT 24000 (62)........................................................................................................................ 3-45

Summary of Contents for RCV144ACx



























































































































































































Reviews:

No comments