Robe BMFL Robin Spot Woreless DMX CRMX User Manual Download Page 8 | Manualshive

Page: 8 / 57

background image

8

4.4 Replacing colour filters

Install colour filters with the device switched off only.

Unplug from mains before!

Colour filters

1. Disconnect the fixture from mains and allow it to cool 10 minutes.

. Remove the plastic cover of the head by loosening the 4 quarter-turn fasteners on the cover.

3. Turn the colour wheel 2 (the colour wheel more closely to the lamp) to the suitable position.

The dichroic filters are fixed on the colour wheel by the magnets.

4. Release the dichroic filter (1) from the colour wheel 2 by inclining it from its position

to break the power of the magnet

. Protect the glass filter with a piece of paper or clout.

5. Insert a new dichroic filter into the colour wheel 2.

6. Place the top cover back before applying power.

«
...
6
7
8
9
10
...
»

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX


























































Reviews:

No comments

Related manuals for BMFL Robin Spot Woreless DMX CRMX

DARTWOOD 100 LED Solar Spotlight

Brand: Wasserstein Pages: 6

Brand: Mobile Power Pages: 8

IP65 ARC COB XL

Brand: PROLED Pages: 4

Brand: EuroLite Pages: 36

Golight Stryker GL-3049-P

Brand: Larson Electronics Pages: 3

Brand: Cameo Pages: 152

Brand: XanLite Pages: 2

Brand: Anslut Pages: 16

Brand: Stagg Pages: 10

Brand: Heitronic Pages: 8

Brand: Heitronic Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands