30
R. Gobo Index 2/6
channel 64
channel 56
Prism
channel 65
channel 57
Prism Rot
channel 66
channel 58
Prism
channel 67
channel 59
Zoom
channel 68
channel 60
Frost /
channel 69
channel 6
Frost /
channel 70
channel 6
Frost /
channel 7
channel 63
Frost /
channel 7
channel 64
Focus
channel 73
channel 65
Focus
channel 74
channel 66
Iris
channel 75
channel 67
Strobe /
channel 76
channel 68
Strobe /
channel 77
channel 69
Strobe /
channel 78
channel 70
Strobe /
channel 79
channel 7
Dimmer /
channel 80
channel 7
Dimmer /
channel 8
channel 73
Dimmer /
channel 8
channel 74
Dimmer /
channel 83
channel 75
Diffusor
channel 84
channel 76
After having calibrated all effects, touch the [confirm] to save adjusted values and reset the fixture.
Load Default Calibrations
- The item loads default (factory) calibration values.
Calibrate Pan/Tilt EMS
- This menu item allows calibration of the pan/tilt
electronic motion stabilizer.
Important: during this calibration any external force must not influence the fixture and the surface at which
the fixture stands (or truss if the fixture hangs) has to be without movement, shake, strokes etc.
Updating software
-
The menu item allows you to update software in the fixture via either serial or USB port
of PC.
The following are required in order to update software:
- PC running Windows 95/98/2000/XP/7/8 or Linux
- DMX Software Uploader
- Flash cable RS232/DMX No.13050624 (if you want to use a serial port of PC)
- Robe Universal Interface (if you want to use an USB port of PC)
Note: Software update should execute a qualified person. If you lack qualification, do not attempt the
update yourself and ask for help your ROBE distributor.
DMX address, IP address, programs -3 and all items in the menu "Personality" will be set to their default
(factory) values.
To update software in the fixture:
I. Installation of the DMX Software Uploader.
. DMX Software Uploader program is available from the ROBE web site at WWW.robe.cz.
2. Make a new directory ( e.g. Robe_Uploader) on your hard disk and download the software to it.
3. Unpack the seftware.
II.Fixture software updating.
.Determine which of your ports is available on your PC and connect it:
- with the DMX input of the fixture if you using the flash cable RS232/DMX
- with the DMX output of the Robe Universal Interface if you using the USB cable.
Disconnect the fixture from the other fixtures in a DMX chain. Turn both the computer and
the fixture on. Make sure the lamp is switched off (only if the fixture involves a lamp).
2. Switch the fixture to the updating mode by touching the "Updating Software " item
Note: If you do not want to continue in software update, you have to switch off and on the fixture
to escape from this menu.
We recommend to cancel all running programs before starting the Software Uploader.
3. Run the Software Uploader program. Select desired COM and then click on the Connect button.
(Select COM if the serial port is used or Robe Universal Interface if the USB port is used).
If the connection is OK, click on the “Start Uploading button“ to start uploading. It will take several
minutes to perform software update.
If the option "Incremental Update" is not checked, all processors will be updated (including
processors with the same software version).
If you wish to update only later versions of processors, check the “Incremental Update box“.
Summary of Contents for BMFL Robin Spot Woreless DMX CRMX
