Robe BMFL Robin Spot Woreless DMX CRMX User Manual Download Page 6

Page: 6 / 57

4. Installation

Fixtures must be installed by a Qualified electrician in accordance with all

national and local electrical and construction codes and regulatio

4.1 Connection to the mains

For protection from electric shock, the fixture must be earthed!

The Robin BMFL Spot is equipped with auto-switching power supply that automatically adjusts to any 50-60Hz

AC power source from 200-240 Volts. The fixture is protected by one 15 A blow primary fuse.

If you install a cord cap on the power cable to allow connection to power outlets, install a grounding-type (earthed)

plug, following the plug manufacturer’s instructions.

To apply power, first check that the head pan and tilt locks are released.

The cores in the power cable are coloured according to the following table.

Core (EU)

Core (US)

Connection Plug Terminal Marking

Brown

Black

Live

Light blue

White

Neutral

Yellow/Green Green

Earth

The earth has to be connected!

If you have any doubts about proper installation, consult a qualified electrician.

Do not connect the fixture to a dimmer system!

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX


























































Search results

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX

Reviews:

Related manuals for BMFL Robin Spot Woreless DMX CRMX

Brands by name

Popular brands

Robe BMFL Robin Spot Woreless DMX CRMX, User Manual

Search results

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX

Reviews:

Related manuals for BMFL Robin Spot Woreless DMX CRMX

Brands by name

Popular brands