Robe BMFL Robin Spot Woreless DMX CRMX User Manual Download Page 12 | Manualshive

Page: 12 / 57

background image

Omega holders positions:

Truss installation

1.

Bolt each clamp (1) to the omega holder (2) with M12 bolt and lock nut through the hole in the holder.

2.

Fasten the omega holders to the bottom of the base by inserting both quick-lock fasteners (3) into

the holes of the base and tighten fully clockwise.

3.

Clamp the fixture on a truss (6) and tighten the rigging clamps.

4

. Pull one safety wire (4) around the truss (6) and through the handle (7) and another safety wire (4) pull

around the truss (6) and through the handle (7) and lock the screw-on carabine through attachment point (5)

as shown on the picture below.

When installing fixtures side-by-side,

avoid illuminating one fixture with another!

DANGER TO LIFE!

Before taking into operation for the first time,the installation has to be approved by

an expert!

1

-Clamp

2

-Omega holder

3

-Quick-lock fastener

4

-Safety wire

5

-Attachment point

6

-Truss

7

-Handle

«
...
10
11
12
13
14
...
»

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX


























































Reviews:

No comments

Related manuals for BMFL Robin Spot Woreless DMX CRMX

Brand: Wagan Pages: 16

Brand: ADB Stagelight Pages: 12

Brand: Targa Pages: 58

IR666-5W DOOMSTER POWER

Brand: VELAMP Pages: 16

Brand: RUSTA Pages: 32

Brand: Telco Pages: 5

Brand: Titanium Pages: 4

Brand: Light-ink Pages: 10

Brand: Stahl Pages: 20

Brand: Foxfury Lighting Solutions Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands