Robe BMFL Robin Spot Woreless DMX CRMX User Manual Download Page 35

Page: 35 / 57

Gobo Carousel 2 Error 1 (Gobo Carousel 2 Error 2 )

The messages will appear after the reset of the gobo carousel if this wheel is not located in the default posi-

tion.

Gobo rotation 2 Error 1 (Gobo Rotation 2 Error 2 )

The messages will appear after the reset of the rotating gobo wheel if the rotating gobos are not located in

the default positions.

Faulty battery

The battery on the display board is exhausted and should be replaced immediately.

Vcc 5V failure

The 5V supply failure has appeared.

Vcc 48V failure

The 48V supply failure has appeared.

Lamp Fan Bad, Lamp Off

One of the blowers (Fan 1, Fan 2) cooling the lamp malfunctioned and the lamp was switched off.

Front Fan Bad, Lamp Off.

One of the sucking fans (Fan 6, Fan 7) in the fixture head malfunctioned and the lamp was switched off.

Base Fan Bad, Lamp Off

One of the fans (Fan 5, Fan 6) in the fixture base malfunctioned and the lamp was switched off.

CMY Fans Bad, Lamp Off

Both fans (Fan 3, Fan 4) in the CMY module in the fixture head malfunctioned and the lamp was switched

off.

CMY Fan Bad, Lamp P. Reduced

One of the fans (Fan 3, Fan 4) in the CMY module in the fixture head malfunctioned and the lamp power has

been reduced.

Gobo Fan Bad, Lamp P. Reduced

The gobo blower (Fan 5) at gobo wheels in the fixture head malfunctioned and the lamp power is reduced when

the gobo wheel 1 (2) or animation wheel is moving into the light beam.

Arm Fan Bad

The small fan (Fan 8) in the fixture arm malfunctioned.

Fans location:

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX


























































Search results

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX

Reviews:

Related manuals for BMFL Robin Spot Woreless DMX CRMX

Brands by name

Popular brands

Robe BMFL Robin Spot Woreless DMX CRMX, User Manual

Search results

Summary of Contents for BMFL Robin Spot Woreless DMX CRMX

Reviews:

Related manuals for BMFL Robin Spot Woreless DMX CRMX

Brands by name

Popular brands