manualshive.com logo in svg

RLE Technologies WiNG-MGR, User Manualline

Share
Download
RLE Technologies WiNG-MGR User Manualline Download Page 34

34

WiNG-MGR User Guide

800.518.1519

3

  Web Interface

Battery Run Hours

Enter the number of hours the sensor has been running. Set this 

value to 0 each time you replace the battery if you are manually 

tracking battery life.

Battery Hour Limit

Designate the number of hours the battery on the sensor can run 

before a battery alarm notification is triggered.

Alarm Notifications

Temp Over

Enter a high temperature alarm threshold - if the temperature rises 

above this value, a high temperature alarm is generated.

Temp Under

Enter a low temperature alarm threshold - if the temperature drops 

below this value, a low temperature alarm is generated.

Humidity Over

Enter a high humidity alarm threshold - if the humidity rises above 

this value, a high humidity alarm is generated.

Humidity Under

Enter a low humidity alarm threshold - if the humidity drops below 

this value, a low humidity alarm is generated.

Leak Threshold

This number represents the uA of current that must be present on 

the leak detection sensing cable in order to trigger an alarm. 
If you are seeing a large number of false alarms, even after 

cleaning the cable, our tech support staff may work with you to 

adjust this threshold.

Default = 4

Alarm Delay

The number of seconds that pass between the time the system 

goes into alarm and the time that alarm is annunciated.

Relay Upon Alarm

If the sensor goes into alarm, will it activate a relay? If so, designate 

which relay or relays it will activate, and check the appropriate 

boxes for which conditions the relay should be activated.

Default = None

Warning Notifications

Temp Over

Enter a high temperature warning threshold - if the temperature 

rises above this value, a high temperature warning is generated.

Temp Under

Enter a low temperature warning threshold - if the temperature 

drops below this value, a low temperature warning is generated.

Humidity Over

Enter a high humidity warning threshold - if the humidity rises above 

this value, a high humidity warning is generated.

Humidity Under

Enter a low humidity warning threshold - if the humidity drops below 

this value, a low humidity warning is generated.

Warning Delay

The number of seconds that pass between the time the system 

goes into a warning state and the time that warning is annunciated.

Gain/Offset Settings

 - Applicable only for WiNG-ANLG analog sensors. Using the formulas 

below, adjust the gain and offset values approproately to fine tune your sensor’s accuracy.

Option

Description

Table 3.4

Individual Sensor Page - Sensor Configuration Tab Options

Summary of Contents for WiNG-MGR







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands