manualshive.com logo in svg

RITZ ICO 245, User Manual, Page: 33 / 50

Share
Download
RITZ ICO 245 User Manual Download Page 33

Please observe the following instructions:
» A total of no more than 0.5 litres of oil may be drawn from a

transformer over its entire service life.

» Oil sampling should only be carried out at temperatures of at

least +5 °C.

» Should problems arise when drawing oil, please contact us

immediately: 

Ò

 Chapter 7 Contact / customer service

on page 47

» You can obtain the oil sampling set directly from the manufac‐

turer: 

Ò

 Chapter 7 Contact / customer service on page 47

CAUTION

Leakage during operation
In rare cases, leaks may occur during operation of the high voltage
transformer. There is a risk of injury and explosion!
» Regularly inspect the transformer for damage.
» In the event of a malfunction, immediately disconnect the

transformer from the mains and contact the customer service.

3.2  Troubleshooting

In rare cases, faults may occur during operation of the device.

» Disconnect  the  switchgear  from  the  power  supply 

Ò

  Chapter

2.1.1 Working disconnected from voltage on page 13.

» First check the connections according to the table below.
If  the  measures  listed  below  do  not  rectify  the  fault  or  if  other  faults
not listed here occur, please contact us (

Ò

 Chapter 7 Contact / customer

service on page 47).

ICO 72,5...245

USER MANUAL
When to interrupt the running operation

 

 

30/47

Summary of Contents for ICO 245



















































Reviews:

No comments