manualshive.com logo in svg

RITZ ICO 245, User Manual, Page: 20 / 50

Share
Download
RITZ ICO 245 User Manual Download Page 20

Cleaning of the contact surfaces
» Use a grease-dissolving cleaning agent such as white

spirit or acetone.

» Use a soft cloth or, if necessary, fine sandpaper to avoid

scratching the contact surfaces.

NOTICE

Do not use wire brushes when cleaning aluminium or
galvanised contact surfaces!

After cleaning, apply a thin layer of contact grease to the contact
surfaces.  Only  use  auxiliary  materials  recommended  and
approved  by  the  manufacturer,  e.g.  Penatrox,  special  grease
Pfisterer MV.

CAUTION

Safe handling of auxiliary materials
Health hazards can arise from the auxiliary materials used,
depending on their chemical composition.
» It is essential to observe the safety datasheets of the

auxiliary materials, and the instructions and regulations
they contain.

5.

Establish the primary connection at the transformer:
Screw  the  two  primary  terminals  on  the  transformer  to  the
stranded conductor or rail of the switchgear.

Observe the required tightening torques, see 

Ò

 Table on page 19

ICO 72,5...245

USER MANUAL

How to use this device as intended

 

 

17/47

Summary of Contents for ICO 245



















































Reviews:

No comments