RITE-HITE FROMMELT SAFETY PRODUCTS GUARDIAN DEFENDER, Manual

Page: 21 / 48

PUB. NO. DFNDRB JANUARY 2013 21
DEFENDER ™
FEATURE RICH - I-COMM INSTRUCTIONS
PROCEDURE FOR USING DOWNLOADER CHIP:
1. Turn power off.
2. Plug in downloader chip.
3. Turn power on.
4. Press ENTER.
5. Scroll to “Copy From Loader”.
6. Press ENTER and UP key to start copy process.
7. When complete, turn power off and remove loader.
8. Restore power and operate door.
PROCEDURE FOR ADJUSTING RECLOSE TIMER:
1. Press ENTER key.
2. Use UP key to scroll to “Set Close Timer”.
3. Press ENTER key.
4. To increase reclose time, press UP key.
5. To decrease reclose time, press DOWN key.
6. Press ENTER when complete.
7. Scroll to EXIT.
8. Press ENTER to save changes.
PROCEDURE FOR CHECKING FAULT HISTORY:
1. Press ENTER key.
2. Use UP / DOWN keys to scroll to “Fault History”.
3. Press ENTER key.
4. This displays the last 5 faults in numerical code.
5. For a detailed view, press the UP key to scroll through the
fault codes.
6. Press ENTER when complete.
7. Scroll to EXIT.
8. Press ENTER, operate door.
The following describes what the fault codes convert to:
Description Code
#define FaultNone 0
#define FaultPowerUp 1
#define FaultBreakaway 2
#define FaultRunOpenTimer 3
#define FaultMenuInt 4
#define FaultLimitSwitch 5
#define FaultEstop 6
#define FaultRunCloseTimer 7
#define FaultLimitPulseFail 8
#define FaultObstruction 9
#define FaultTimerRead 0A
#define FaultStateOB 0B
#define FaultPROSystem 0C
#define FaultPhotoeye 0D
#define FaultEncoderRead 0E
#define FaultEncoderVelocity 0F
#define FaultEncoderNC 10
CONNECTOR
FLASHING LAMP OUT
UNUSED
DC POWER OUT
RESET INPUT (X12)
UNUSED
DC COMMON INPUT
DC POWER INPUT
24VAC INPUT
24VAC COMMON (N)
OPEN/CLOSE COM
CLOSE OUTPUT (K1)
OPEN OUTPUT (K0)
LOOP INPUT 2
LOOP INPUT 1
DC POWER OUT
DC COMMON OUT
DC POWER OUT
LOOP INPUT (X13)
PIN #
1
2
3
4
1
2
3
4
5
6
7
8
1
2
3
4
5
6
FLASHING LAMP OUT
I-ZONE ALARM OUT
DC POWER OUT
RESET INPUT (X12)
UNUSED
DC COMMON INPUT
DC POWER INPUT
24VAC INPUT
24VAC COMMON (N)
OPEN/CLOSE CO
CLOSE OUTPUT (K1)
OPEN OUTPUT (K0)
LOOP INPUT 2
LOOP INPUT 1
DC POWER OUT
DC COMMON OUT
DC POWER OUT
LOOP INPUT (X13)
UNUSED OUTPUT
I-ZONE ALARM OUT
DC POWER OUT
RESET INPUT (X12)
UNUSED
DC COMMON INPUT
DC POWER INPUT
24VAC INPUT
24VAC COMMON (N)
OPEN/CLOSE COM
CLOSE OUTPUT (K1)
OPEN OUTPUT (K0)
LOOP INPUT 2
LOOP INPUT 1
DC POWER OUT
DC COMMON OUT
DC POWER OUT
LOOP INPUT (X13)
FLASHING LAMP OUT
UNUSED
DC POWER OUT
RESET INPUT (X12)
UNUSED
DC COMMON INPUT
DC POWER INPUT
24VAC INPUT
24VAC COMMON (N)
OPEN/CLOSE COM
INVERTER OUT 2(K1)
INVERTER OUT 1 (K0)
LOOP INPUT 2
LOOP INPUT 1
DC POWER OUT
DC COMMON OUT
DC POWER OUT
LOOP INPUT (X13)
FLASHING LAMP OUT
UNUSED
DC POWER OUT
RESET INPUT (X12)
UNUSED
DC COMMON INPUT
DC POWER INPUT
UNUSED
UNUSED
OPEN/CLOSE COM
CLOSE OUTPUT (K1)
OPEN OUTPUT (K0)
LOOP INPUT 2
LOOP INPUT 1
DC POWER OUT
DC COMMON OUT
DC POWER OUT
LOOP INPUT (X13)
J3
J4
J5
This table shows the function of each of the connectors on the i-COMM controller. The voltages listed for each pin
assume that either the input or output is activated.