Riello RESIDENCE 25 KIS, Installer And User Manual

Page: 12 / 140

12
RESIDENCE
SETTINGS MENU TREE STRUCTURE
Below is a list of the parameters that can be programmed; if the adjustment board does not support the relative function, the interface
returns an error message:
The remote control has the function of a machine interface, displaying the system settings and providing access to the parameters.
7KHGLVSOD\QRUPDOO\VKRZVWKHWHPSHUDWXUHRIWKHÀRZVHQVRUXQOHVVWKHUHLVDGRPHVWLFKRWZDWHUUHTXHVWLQSURJUHVVWKHQWKHGRPHV
-
tic hot water probe temperature is displayed; if no key is touched within 10 sec the current time is displayed (backlight unlit).
7KHFRQ¿JXUDWLRQ0(18LVRUJDQLVHGZLWKDPXOWLOHYHOWUHHVWUXFWXUH$QDFFHVVOHYHOKDVEHHQ¿[HGIRUHDFKVXEPHQX86(5OHYHO
always available; TECHNICAL level password protected.
%HORZLVDVXPPDU\RIWKH6(77,1*60(18WUHHVWUXFWXUH
6RPHRIWKHLQIRUPDWLRQPLJKWQRWEHDYDLODEOHGHSHQGLQJRQWKHDFFHVVOHYHOWKHVWDWXVRIWKHPDFKLQHRUWKHV\VWHPFRQ
-
¿JXUDWLRQ
Menu Parameter Value
Level
password
Value set
in the factory
Personalised
values
SETTINGS
TIME USER
TIME PROGRAMM USER
COMB
GAS TYPE 0 / 1 INSTALLER 0
BOYLER TYPE 1/2/3 SERVICE
1 (25k W)
2 (30k W)
3 (35k W)
COMBUSTION OFFSET 0 / 1 / 2 SERVICE
CONF
HYDRAULIC CONFIGURATION 0 / 1/ / 2 / 3 / 4 INSTALLER 1
WATER TRANSDUCER 0 / 1 SERVICE 1
AUTO WATER FILL ENABLE 0 / 1 SERVICE 0
BEGIN SYSTEM FILLING NOT AVAILABLE ON THIS MODEL
AIR PURGING CYCLE 0 / 1 SERVICE 1
MIN INSTALLER
see technical data
table
MAX INSTALLER
see technical data
table
MAX_CH MIN - MAX INSTALLER
see technical data
table
RANGE RATED MIN - MAX_CH INSTALLER
see technical data
table
DO_AUX1 0 / 1 / 2 INSTALLER 0
EXHAUST PROBE RESET 0 / 1 INSTALLER 0
CH
HYST ON HIGH TEMP 2 - 10 SERVICE 5
HYST OFF HIGH TEMP 2 - 10 SERVICE 5
HYST ON LOW TEMP 2 - 10 SERVICE 3
HYST OFF LOW TEMP 2 - 10 SERVICE 3
PUMP CONTROL TYPE 0 - 100 INSTALLER 85
CH POSTCIRC NOT AVAILABLE ON THIS MODEL
LOW NOISE NOT AVAILABLE ON THIS MODEL
SCREED HEATING 0 / 1 INSTALLER 0
ANTI CYCLE FUNCTION 0 - 20min INSTALLER 3min
RESET CH TIMERS 0 / 1 INSTALLER 0
MAIN ZONE ACTUATION TYPE 0 / 1 INSTALLER 0
MAIN ZONE ADDR 1 - 6 INSTALLER 3
MAIN ZONE HYDRAULIC CONF 0 / 1 INSTALLER 0
MAIN ZONE TYPE 0 / 1 INSTALLER 0
MAX CH SET
AT: MIN CH SET - 80.5
BT: MIN CH SET - 45.0
INSTALLER
80.5
MIN CH SET
AT: 40 - MAX CH SET
BT: 20 - MAX CH SET
INSTALLER 40
OTR 0 (default) / 1 INSTALLER 0