10
9
OPERATION INSTRUCTION
1.Right way to load the currency
Please load currency the machine same as the following steps.
2.Hopper adjustement - the
tight procedure to adjust
the Up/Down screw
Due to long transportation or
use, the screw will be loose.
When the counting is not
accurate, it is necessary to
urn the up/down screw
clockwise to increase the
friction.
3.The right procedure to
change the wear and tear parts
When the rubber tongue is
worn out, please flip it and use
the other side.
ERROR - MESSAGE DISPLAY
Code n°
Problems
Solutions
EE1
The suspicious currency is being
checked out by UV
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EE2
The suspicious currency is being
checked out by MG
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EE3
The suspicious currency is being
checked out by IR
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EE4
- The half currency is being
checked out
- The left (right) counting sensor is
dirty or brocken
- Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
- To clean it or change a new one
EE5
Two pieces currency are counted
as one/inaccurate counting
To tight the adjustable screw
clockwise
EE6
The suspicious currency with
different located magnetic is
being checked out by MG
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EE7
Slanting currency is being
checked out
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EE8
The currency width is smaller than
30mm
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EE9
The currency width is longer than
85mm
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EEA
Chain currency is being checked
out
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
EEB
Broken currency is being checked
out
Take out the first currency (sus-
picious currency) in the stacker,
then press « RESET » to continue
Code n°
Causes
Solutions
E01
The left counting sensor is broken or dirty
To clean it or change a new one
E02
The right counting sensor is broken or dirty
To clean it or change a new one
E03
The code disc is dirty or loosen
To clean it or tight it
E04
The hopper sensor is brocken or dirty
To clean it or change a new one
E05
The stacker sensor is broken or dirty
To clean it or change a new one
E07
Ambient magnetic field is too strong
To lower the ambient magnetic field
E07
MG is not workable
To change a new one
E10
Ambient light is too high
To lower the ambient light
E10
UV sensitivity light is too high
To lower the UV light
E11
The connector of front display is loosen
To tight the connector
Currency
Photo 3.1.1
Photo 3.1.2
Currency
Adjust the up/down screw
tighten
loosen
4. Troubleshooting
Note : when counting and detecting is not accurate, please check the
machine as follows :
No power
The power line
cord is connected
well?
The fuse is worn
out
The power switch
is on
The power is on,
but no working
The hopper sen-
sor is dirty, please
clean by brush
Connect the
hopper sens or
line well to the
main board
The belt is too
loose or too tight,
adjust the belt
Wrong counting
Turn the screw
clockwise to
increase the
friction
Counting sensor
is dirty, please
clean it
The 6 rubber
wheels are worn
out, please
replace them
Wrong detecting
Adjust the MG
sensor
MG is dirty, please
clean it
UV sensor is
broken or dirty,
please clean it or
replace with new
one
