manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Installation & Operating Instructions Manual, Page: 8 / 70

Share
Download
Republic Manufacturing RB-SERIES Installation & Operating Instructions Manual Download Page 8

www.republic-mfg.com

800.847.0380

8

Installation

 

Lift the blower system by the lifting eye mounted on the top of the motor or by picking the blower up from underneath 

the motor. Do not lift the blower by the belt guard. Vibration isolators are included with every blower. Bolt your Republic 

Blower in place by the mounting brackets supplied with the blower. Use a minimum of four (4) mounting bolts. See the 
Specifications Section of the manual for equipment weights. No training required.

1.

 

Have a qualified electrician configure the motor to your incoming voltage as noted in the Motor Wiring Section of the 
manual. Refer to the nameplate on the motor for the correct power supply requirements.

2.  The blower should be located in a place where the drive belt and intake air filter can be easily serviced and maintained.

3.  Avoid any type of liquid over-spray or continuous washdown of the blower. Shield the blower if needed. Flooding the 

blower can cause damage to the system.

4.  Double check the pulley alignment and install the belt as shown in the Motor Pulley and Installation Belt diagrams. Be 

sure to re-fasten the belt guard.

5.  Install the inlet air filter – improper filtration will void warranty. Install system piping and check motor amperage draw. 

High amperage draw may indicate too much flow. Contact Republic Manufacturing or the local distributor with any 
questions.

6.   Ensure unit has unobstructive surrounding space of 3 feet (0.91 m) with 10 inches (254 mm) space in front of belt guard.

Frequency of Inspection

Filter

Weekly

Belt

Monthly

Grease motor (if applicable)

Quarterly

Keep blower free from contaminants

Monthly

Summary of Contents for RB-SERIES







































































Reviews:

No comments