manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Installation & Operating Instructions Manual, Page: 29 / 70

Share
Download
Republic Manufacturing RB-SERIES Installation & Operating Instructions Manual Download Page 29

800.847.0380

www.republic-mfg.com

29

Water-Cooled Balanced Bearing Housing Assembly

Note: Bearing Housing Assembly sold as a 

balanced unit with specified pulley.

Blower 

Pulley

Bearing Housing Assembly Part Number

RB500

RB800/1200HC/2400 RB2000 RB4000

231-1005

200-8105WC

Not Available

Not Available Not Available

231-1015

200-8115WC

231-1025

200-8125WC

231-1035

200-8135WC

231-0145

200-8145WC

200-9145WC

231-0155

200-8155WC

200-9155WC

231-0165

200-8165WC

200-9165WC

231-0175

200-8175WC

200-9175WC

200-2175WC

231-0185

Not Available

200-9185WC

200-2185WC

231-0195

200-9195WC

200-2195WC

231-0205

200-9205WC

200-2205WC

231-0215

200-9215WC

200-2215WC

231-0225

200-9225WC

200-2225WC

231-0235

200-9235WC

200-2235WC

231-0245

200-9245WC

Not Available

231-0255

200-9255WC

231-0265

200-9265WC

231-0275

200-9275WC

200-7275WC

231-0285

200-9285WC

Not Available

231-0295

200-9295WC

200-7295WC

231-0305

Not Available

Not Available

231-0315

200-7315WC

231-0325

Not Available

231-0335

200-7335WC

231-0345

Not Available

231-0355

200-7355WC

231-0365

Not Available

231-0375

200-7375WC

231-0385

Not Available

231-0395

200-7395WC

Summary of Contents for RB-SERIES







































































Reviews:

No comments