manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Installation & Operating Instructions Manual, Page: 19 / 70

Share
Download
Republic Manufacturing RB-SERIES Installation & Operating Instructions Manual Download Page 19

800.847.0380

www.republic-mfg.com

19

Mounting Bolt Length**

Torque for Fastening Screws

Hardware is provided with each retro kit. User is responsible for making sure the length of the screws is appropriate 

for the motor being attached. Screws that are too long may contact the motor windings and cause damage. 

Location

Blower

Torque (ft-lbs)

Back Plate to Motor

RB800-RB2400

60

RB4000-RB4002

140

Back Plate to Bearing Housing

RB800-RB4002

24

Tension Pulley

RB800-RB2400

45

Motor Pulley Set Screws

RB500-RB4002

36

Frame Size

Thread 

Specification

Bolt Length

182TC/184TC

1/2-13 UNC

1-1/4”

213TC/215TC
254TC/256TC

284TSC/286TSC

1-1/4” (RB500-RB2000)

2” (RB2400-RB4000)

324TSC/326TSC

1-1/4” (RB500-RB2400)

2” (RB4000)

364TSC/365TSC

2”

90L

M8

20mm

112M

132S

30mm

160M

M12

160L

45mm

180M

5/8-11 UNC (Thru)

2-1/2”

200L

225M
250M

Summary of Contents for RB-SERIES







































































Reviews:

No comments