manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Installation & Operating Instructions Manual, Page: 44 / 70

Share
Download
Republic Manufacturing RB-SERIES Installation & Operating Instructions Manual Download Page 44

www.republic-mfg.com

800.847.0380

44

Straight Edge

0” TO ± 1/32” 

Straight Edge

Middle Hole is 

for Removal

Mounting Plate

Additional two (2) Holes are 

for Installation

Motor Pulley Installation Procedure:

(May be performed by untrained personnel)

1.  Install bushing into motor pulley with set screws. Then install the motor pulley assembly onto the motor’s shaft.

2.  Use a straight edge to align the motor pulley face with the blower pulley face. Alignment must be within 0 inch to 

± 

1/32 

inch (0 mm to ± .792 mm). The straight edge must be able to rotate radially and lay flush on two faces of the motor pulley 

while lying flush on the face of the blower pulley to insure proper alignment 

(see Detail C)

.

3.  Insert a screw driver through one of the motor pulley’s and mounting plate’s holes to keep the motor pulley from rotating 

while tightening the set screws.

4.  Using a torque wrench, set the torque to 36 ft./lbs. (5m/kg) and then torque the set screws equally.

Note:

  This same motor pulley installation procedure applies to the RB2400 Blower.

Motor Pulley Installation

Radially Rotate the 

Straight Edge to Align 

Blower Pulley

Detail C

Summary of Contents for RB-SERIES







































































Reviews:

No comments