manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Installation & Operating Instructions Manual, Page: 5 / 70

Share
Download
Republic Manufacturing RB-SERIES Installation & Operating Instructions Manual Download Page 5

800.847.0380

www.republic-mfg.com

5

Safety Instructions

1.  Always use qualified electrical and mechanical personnel for installation and maintenance of Republic Blowers and 

motors.

2.  Disconnect the electrical power at the motor starter, fuse box or circuit breaker before working on the system. Take 

special precautions to make sure the power cannot be turned on while you are working on the blower. Use an 
approved lockout/tagout system.

3.  Make sure the motor is electrically grounded, the mounting bolts are properly secured, and all guards are in place 

before start-up.

4.  Wear safety glasses and earplugs when working on the blower, air knife or discharge nozzles within  

 

 

a Republic Blower system.

5.  Do not operate blower/motor assembly with the belt guard removed. 

6.  Do not operate blower with the outlet open to atmosphere. Connect system piping or butterfly valve to prevent 

overloading the motor. Check the final installation for proper amp loads.

7.  Keep all tools, loose clothing and hands away from rotating or moving parts while the unit is running. Never run the 

blower unit without the belt guard installed.

8.  Inspect the blower at regular intervals for damaged or worn parts. Replace damaged parts immediately! Do not 

connect or turn on a damaged blower!

9.  Inspect the inlet air filter at regular intervals and replace when necessary. A dirty air filter can cause improper blower 

performance.

10.   Flanged blower housing gasket must be installed. Check for leaks.

11.  Ensure blower rotation is correct.

12.  Use only genuine Republic Blower brand replacement parts.

13.  Refer to Troubleshooting section of manual. 

14.  Make sure to install the inlet air filter or piping to blower inlet before starting the blower/motor.

15.  Water, other liquids, aggressive or inflammable gases and vapors may not be handled. Handling of inflammable or 

aggressive gases and vapors is only possible with special versions that have not been CE Certified.

PROTECT EYES & EARS

Moving parts can crush and 

cut.

Do not operate with guard 

removed.

Lock-out/tagout before 

servicing.

WARNING

Summary of Contents for RB-SERIES







































































Reviews:

No comments