manualshive.com logo in svg

Republic Manufacturing RB-SERIES, Installation & Operating Instructions Manual, Page: 45 / 70

Share
Download
Republic Manufacturing RB-SERIES Installation & Operating Instructions Manual Download Page 45

800.847.0380

www.republic-mfg.com

45

Blower Pulley

Motor

Taper-Lock 

Bushing

Set 

Screws

Motor Pulley Face

Blower Pulley Face

1/2-13 Hex Head 

Screw 4 Pls

Note:

  Tension Pulley has been removed  

       

 

in the views for clarity purposes.

Motor Pulley Removal Procedure:

(May be performed by untrained personnel)

1.  Line up one motor pulley hole to mounting plate hole and insert a screw driver through, restricting the motor pulley rotation.

2.  Use a 1/4 inch (6.35 mm) Allen wrench and remove the two (2) set screws from the motor pulley and bushing.

3.  Insert one of the removed set screws into the top middle hole of the bushing.

4.  While still keeping the motor pulley from rotating, tighten the middle hole set screw until the motor pulley separates from the 

bushing.

5.  When the motor pulley is loose, slide it off the motor shaft.

6.  Be careful not the drop the motor pulley and damage the grooves.

Note:

  This same motor pulley installation procedure applies to the RB2400 Blower.

Middle Hole in Bushing is 

for Removal

Set Screw 

Installation Holes

Motor Pulley Removal Procedure

Mounting Plate

Mounting Plate Hole

Detail A

Summary of Contents for RB-SERIES







































































Reviews:

No comments