Renesas mPD98431 User Manual Download Page 81

Page: 81 / 127

CHAPTER 4 REGISTER DESCRIPTION

User’s Manual S14054EJ4V0UM

MACC3 - MAC configuration register 3 (register address A[7:0] = 90H) R/W

PTIME[15:0]

Reserved

APSE

APSS

BUSMODE BACKPE FLWCNT TXFFLH RXFLH

Bit

Name

Function

Default

31:16

PTIME

Pause timer value.

The value of this field is used as a pause timer value when the

PD98431

generates a pause control frame.

FFFFH

15:7

–

Reserved. Write 0 to these bits.

APSE

Status information append (suffix).

When this bit is 1, the status information of a receive packet is suffixed to

the receive data stream read from the FIFO bus.

APSS

Status information append (prefix).

When this bit is 1, the status information of a receive packet is prefixed to

the receive data stream read from the FIFO bus.

Caution Do not set the APSE and APSS bits to 1 at the same time.

BUSMODE

Little endian/big endian.

When this bit is 1, the byte order of the FIFO bus is big endian.

BACKPE

Back pressure enable.

When this bit is 1, the back pressure function is enabled.

FLWCNT

Transmission flow control enable.

When this bit is 1, automatic transmission of the pause control frame is

enabled.

TXFFLH

Transmit FIFO flash.

When this bit is set to 1, all the contents of the transmit FIFO are cleared.

To clear this function, write 0 to this bit.

RXFFLH

Receive FIFO flash.

When this bit is set to 1, all the contents of the receive FIFO are cleared.

To clear this function, write 0 to this bit.

Remark

When switching the settings of bits other than the PTIME bit, be sure to execute software reset after

setting the registers. Refer to

3.16 (4) Cautions on switching settings of MACC1, MACC2, MACC3,

PCSC registers

Summary of Contents for mPD98431
































































































































Search results

Summary of Contents for mPD98431

Reviews:

Brands by name

Popular brands

Renesas mPD98431, User Manual

Search results

Summary of Contents for mPD98431

Reviews:

Brands by name

Popular brands