Renesas M34286T2-CPE User Manual Download Page 34

Page: 34 / 70

M34286T2-CPE User’s Manual

2. Setup

R20UT0214EJ0200 Rev.2.00

Page 34 of 70

Sep 16, 2010

2.9 Downloading Firmware

2.9.1 When It is Necessary to Download Firmware

It is necessary to download the firmware in the cases listed below.

(1)

When the firmware has been upgraded

(2)

When M3T-PD72M has been upgraded

If the download is not completed in the cases below, redownload the firmware.

- When the power is unexpectedly shut down during a download from M3T-PD72M

- When a communications interface cable is unexpectedly pulled out

2.9.2 Downloading Firmware in Maintenance Mode

Download the firmware in the maintenance mode as explained here following.

The user system must not be

connected when you download the firmware.

(1) Connect the USB interface cable to the emulator and host machine.

(2) Within 2 seconds of activating power to the emulator, press the system reset switch on the emulator to switch to

maintenance mode. When the emulator is switched to maintenance mode, the System Status SAFE LED begins to

flash.

(3) Start up the emulator debugger M3T-PD72M. After setting the Init dialog box, the dialog which urges to download

the firmware will appear. Download the firmware following messages. Required time for downloading the

firmware is about 60 seconds.

IMPORTANT

Note on Downloading Firmware:

•

Do not shut OFF power while the firmware is being downloaded. If the power is shut OFF, the emulator

will not start up properly. If it happened by mistake, redownload the firmware in the maintenance mode.

Summary of Contents for M34286T2-CPE







































































Search results

Summary of Contents for M34286T2-CPE

Reviews:

Related manuals for M34286T2-CPE

Brands by name

Popular brands

Renesas M34286T2-CPE, User Manual

Search results

Summary of Contents for M34286T2-CPE

Reviews:

Related manuals for M34286T2-CPE

Brands by name

Popular brands