background image

 

2

Installation and Operation Manual RTC 12i  - www.regulus.eu

CONTENTS

1. GENERAL INSTRUCTIONS ....................................................................................................  3
 

1.1 Related Documentation ..............................................................................................  3

 

1.2. Safety Instructions .....................................................................................................  3

 

1.3. Cleaning & Maintenance ............................................................................................  3

2. CONNECTION VARIANTS ......................................................................................................  3
 

2.1. Direct connection to a heating system, DHW heating in a hot water storage tank ...........  4

 

2.2. Connection with a thermal store (combination with other renewable heat sources) .. 4

3. CONSTRUCTION READINESS & INSTALLATION ................................................................  4
 

3.1. Scope of supply .........................................................................................................  5

 

3.2. Installation preparation and transport ........................................................................  5

 

3.3. Minimum distances ....................................................................................................  6

 

3.4. Placement of the heat pump ......................................................................................  7

 

3.5. Condensate drain ......................................................................................................  8

 

3.6. Pipe installation .........................................................................................................  9

 

3.7. Electrical wiring ..........................................................................................................  9

4. COMMISSIONING .................................................................................................................. 10
 

4.1. Initial start up ............................................................................................................. 10

 

4.2. Troubleshooting ......................................................................................................... 10

APPENDIX .................................................................................................................................. 11
 

Expanded view ................................................................................................................. 11

 

Internal wiring diagram ..................................................................................................... 12

Summary of Contents for 17448













Reviews: