Regency Fireplace Products Excalibur P90EX Owners & Installation Manual Download Page 56

Page: 56 / 72

Regency Excalibur

P90EX Direct Vent Gas Stove

maintenance

To Remove the Valve Only

Remove pilot nut with 11mm (7/16”) wrench

(Diagram 1). Then remove burner supply tube

from 90 degree brass fitting on valve with 15mm

(5/8”) wrench (Diagram 2). Once the supply

tube has been removed from the 90 degree

brass fitting remove the 90 degree brass fitting

from the valve with a 17 mm (11/16”) wrench

(Diagram 3). Lastly remove supply tube from

valve with 22 mm (7/8”) wrench (Diagram

4).

Note orientation of 90 Degree Brass

fitting.

Remove two (2) Phillips head screws on each

side of the bracket, then remove valve from

mounting bracket.

Diagram 1

Diagram 2

Diagram 3

Diagram 4

Diagram 5

Reverse the steps to reinstall new valve.

Summary of Contents for Excalibur P90EX









































































Search results

Summary of Contents for Excalibur P90EX

Reviews:

Related manuals for Excalibur P90EX

Brands by name

Popular brands

Regency Fireplace Products Excalibur P90EX, Owners & Installation Manual

Search results

Summary of Contents for Excalibur P90EX

Reviews:

Related manuals for Excalibur P90EX

Brands by name

Popular brands