Regency Fireplace Products Excalibur P90EX Owners & Installation Manual Download Page 44 | Manualshive

Page: 44 / 72

background image

44

|

Regency Excalibur

®

P90EX Direct Vent Gas Stove

installation

1.

Remove Arch Surround, if already installed.

2.

Remove glass door. Remove logs.

Note: The logs must not be in the unit when installing

the brick panels.

3.

Insert the back brick panel first by carefully slipping it between the

back wall of the firebox and the rear log bracket.

4.

Put the side panels in next. Slide them in from the front and push

them flat up against the wall. Be very careful not to scratch them on

the firebox hardware.

5.

Install the 2 brick retaining clips, one on each side.

Note:

If the bottom brick panel must be removed: Remove the Rear Log Stand,

then remove the Burner Tray. See the "Removing Valve" section.

Optional Brick Panels

6.

Reverse steps 2-1.

«
...
42
43
44
45
46
...
»

Summary of Contents for Excalibur P90EX









































































Reviews:

No comments

Related manuals for Excalibur P90EX

Brand: Ignis Pages: 12

COLLETTE L-FT629PST-A

Brand: HAMPTON BAY Pages: 6

Brand: HAMPTON BAY Pages: 48

Brand: CACHFIRES Pages: 11

Brand: Napoleon Pages: 4

Brand: Allen + Roth Pages: 48

Nu-way MULTIPLEX ENERGYSTREAM ES Series

Brand: Enertech Pages: 5

Brand: Fire Sense Pages: 7

Brand: Allen + Roth Pages: 40

Brand: Northline Express Pages: 35

Brand: Hargrove Pages: 7

Brentwood Gas Insert

Brand: Pacific energy Pages: 24

Brand: Vanguard Pages: 32

Brand: Outland Living Pages: 6

Brand: Backyard Creations Pages: 6

Brand: Travis Industries Pages: 7

Brand: Bluegrass Living Pages: 8

Brand: Napoleon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands