Regency Fireplace Products Excalibur P90EX Owners & Installation Manual Download Page 30

Page: 30 / 72

Regency Excalibur

P90EX Direct Vent Gas Stove

installation

Rigid Pipe Adaptor

Pipe Length

Vertical

Terminal

Storm Collar

Flashing

943 or 943S

Ceiling Firestop

Pipe

Length

Adj.Pipe Length

90 Elbow

Horizontal

Termination

Cap

Wall Thimble

Vinyl Siding

Standoff (Optional)

Rigid Pipe Venting Systems

The minimum components required for a basic horizontal termination are:

1 Horizontal Termination Cap

1 90

Elbow

1 Rigid Pipe Adaptor

1 Wall Thimble

1 Length of pipe to suit wall thickness

(see chart)

1 4" x 6-5/8" to 5" x 8" increaser for 5" x 8" venting

Wall thickness is measured from the back standoffs to the inside mounting surface

of termination cap. For siding other than vinyl furring strips may be used, instead

of the vinyl siding standoff, to create a level surface to mount the vent terminal.

The Terminal must not be recessed into siding. Measure the wall thickness including

furring strips.

If a Vinyl Siding Standoff is required (it must be used with vinyl siding), measure

to outside surface of wall without siding and add 2 inches.

Horizontal and Vertical

Terminations for 4" x 6-5/8" Venting

Flat Wall Installation

Wall Thickness

(inches)

Vent Length Required

(inches)

4" - 5-1/2"

7" - 8-1/2"

10" - 1-1/2"

12"

9" - 14-1/2"

11" - 14-5/8" Adj. Pipe

15" - 23-1/2"

17" - 24" Adj.

Corner Installation

Wall Thickness

(inches)

Vent Length Required

(inches)

3-1/4" - 6-3/4"

11" - 14-5/8" Adj. Pipe

7-3/4" - 16-1/4"

17" - 24" Adj. Pipe

7-1/4" - 8-3/4"

6" + 12"

9" + 9"

4-1/4" - 5-3/4"

6" + 9"

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

The FPI AstroCap

and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent

Direct Vent, Ameri

can Metal Products Ameri Vent Direct Vent, Olympia Ventis DV, Security Secure Vent

, Selkirk Direct-Temp. AstroCap

is a proprietary trademark of FPI

Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.

This product has been evaluated by Intertek

for using a Rigid Pipe Adaptor in conjunction

with Duravent Direct-Vent, Olympia Ventis DV,

Selkirk Direct-Temp, Ameri Vent Direct venting

and Security Secure Vent systems. Use of these

systems with the Rigid Pipe adaptor is deemed

acceptable and does not affect the Intertek

WHI listing of components.

WARNING:

Do not combine venting components from

different venting systems.

However use of the the AstroCap

and FPI

Riser is acceptable with all systems.

Alternate

Horizontal

Termination

Caps

Summary of Contents for Excalibur P90EX









































































Search results

Summary of Contents for Excalibur P90EX

Reviews:

Related manuals for Excalibur P90EX

Brands by name

Popular brands

Regency Fireplace Products Excalibur P90EX, Owners & Installation Manual

Search results

Summary of Contents for Excalibur P90EX

Reviews:

Related manuals for Excalibur P90EX

Brands by name

Popular brands