Regency Fireplace Products Excalibur P90EX Owners & Installation Manual Download Page 43

Page: 43 / 72

Regency Excalibur

P90EX Direct Vent Gas Stove | 43

installation

920-554

07.15.22

16.

Install the burner. Set the burner aera

tion to 5/16'' (8 mm) for LP. See aeration

adjustment details in the manual.

17.

Open the gas line. Check for gas leaks with

a proper soapy solution or leak detector.

18.

Attach the label "This unit has been

converted to LPG" near or on top of the

serial # decal.

19.

Replace yellow "NG" label with red "LPG"

label.

20.

Reinstall logs, media, door and access

panel. Turn ON the electrical supply.

21.

Turn ON using the remote control (the

remote control is still with the control

module).

22.

Check pilot flames. Correct flame pattern

has 2 strong blue flames. Refer to

"Maintenance Instructions" section of the

manual for correct flame patterns.

23.

Check operation of flame control.

24.

Air shutter should be set to a minimum of

5/16" (8 mm) open.

15.

Slide the control module to remote position.

Remote

Summary of Contents for Excalibur P90EX









































































Search results

Summary of Contents for Excalibur P90EX

Reviews:

Related manuals for Excalibur P90EX

Brands by name

Popular brands

Regency Fireplace Products Excalibur P90EX, Owners & Installation Manual

Search results

Summary of Contents for Excalibur P90EX

Reviews:

Related manuals for Excalibur P90EX

Brands by name

Popular brands