Regency Fireplace Products CF780, Owners & Installation Manual

Page: 20 / 56

An elbow may be installed directly on top of the fireplace if required. Use
the offset option if you need to clear a joist or pass around a cupboard. See
following Diagrams for example.
- In USA : 30° Maximum - In Canada : 45° Maximum
The maximum number of elbows per system is four, resulting in two offsets
and returns.
Install the fireplace and chimney as described earlier. When you require an
elbow, proceed as follows:
1. Install the elbow. Turn it in the desired direction, and fasten it to the other
section with 4 metal screws at the joints.
2. Install enough lengths to obtain the desired offset. Secure each joint with
4 metal screws.
3. Use another elbow to return the chimney to the vertical direction. Again
fasten it to the other section with 4 metal screws at the joints.
4. Install a roof support, a wall support, or an offset support above each
offset to support the weight of the chimney (elbows are not designed to
support the chimney above an offset).
NOTE: 'Through the wall offset' installation requires installa-
tion of the gravity kit along with chase ventilation grills.
Failure to do so could result in severe overheating of the fireplace
chase cavity.
z
0
�
:s
z
1-1
26
Radiation Shield
Use Offset Support
or Roof Support
Refer to
"Canada
Only'' section if
installed in Canada
Radiation
Shield
Flashing
with
Storm Collar
and Roof Top
Radiation Shield_____._....,.��
Insulation
Refer to "Canada
Only''
section if
installed in Canada �����
Offset, Roof
or Wall Support
Ceiling Clearance
see Table 6
Figure 14 Offset
Installation Example
Chimney Figure 15 Offset Chimney Through
a Wall Example
Table 6 Through the Wall Installation Dimensions
30 ° Offset Through the 45 ° Offset Through the
Wall Wall
US and Canada Canada Only
Minimum required
12'3" 10' 6"
11' 10" if not using the 10' 1" if not using the
ceiling heightA
bottom standoff bottom standoff
Height of the
9' 9¼"
8' 9"
center of the hole
9' 4"
if not using the 8' 3½" if not using the
in the wallA bottom standoff bottom standoff
Minimum height of
53" 35½"
the hole
Position of the hole
Centered on the chimney coupling of the fireplace or on the
fireplace casinq (not on the quillotine bay at the front)
Minimum width of
18"
the hole
A These heights assumed that the first elbow is directly on the fireplace as depicted in
Figure 15. If this is not the case, these heights have to be increase by the length of
chimney installed on the fireplace before the first elbow.
Offset Chimney Installation Example
Note: Nailing strips differ than shown in diagram
Offset Chimney Through a Wall Example
You can also go through a wall at an angle starting directly at the fireplace as
depicted in Diagram below. An angled wall insulated radiation shield must be
used wherever the chimney passes through an exterior wall.
Make sure to have enough ceiling height for your installation. If the ceiling height
is too low for the planned installation you may want to consider installing the
fireplace in an outside chase.
Refer to the angled wall insulated radiation shield installation sheets for detailed
installation instructions.
Through the Wall Offset:
Gravity Kit must be installed
z
0
�
:s
z
翿 �
26
Radiation Shield
Use Offset Support
or Roof Support
Refer to
"Canada
Only'' section if
installed in Canada
Radiation
Shield
Flashing
with
Storm Collar
and Roof Top
Radiation Shield
Insulation
Offset, Roof
or Wall Support
Ceiling Clearance
see Table 6
Figure 14 Offset
Installation Example
Chimney Figure 15 Offset Chimney Through
a Wall Example
Table 6 Through the Wall Installation Dimensions
30 ° Offset Through the 45 ° Offset Through the
Wall Wall
US and Canada Canada Only
Minimum required
12'3" 10' 6"
11' 10" if not using the 10' 1" if not using the
ceiling heightA
bottom standoff bottom standoff
Height of the
9' 9¼ "
8' 9"
center of the hole
9' 4"
if not using the 8' 3½" if not using the
in the wallA bottom standoff bottom standoff
Minimum height of
53" 35½"
the hole
Position of the hole
Centered on the chimney coupling of the fireplace or on the
fireplace casinq (not on the quillotine bay at the front)
Minimum width of
18"
the hole
A These heights assumed that the first elbow is directly on the fireplace as depicted in
Figure 15. If this is not the case, these heights have to be increase by the length of
chimney installed on the fireplace before the first elbow.
Gravity Kit
Anchor plate
Anchor plate
1 (D)
Offset Chimney
20
|
CF780 Wood Fireplace
installation