REDT R&D MAGIC-70 Page 9 Manual Download

Page: 9 / 128

3) MagicArt S/W Program Installation

Place the CD in your computer`s CD driver, Follow the below instructions to install the S/W. Install program will be

automatically executed and program installation will be progressed in the following order. If Install program is not

automatically executed after CD is entered, execute Install program on My Computer’s CD drive.

Setup wizard

2. Select installation folder

3. Confirm installation

4. The file is copied onto the hard disk.

5. Click “Close” button to complete program

installation.

6. Once program installation is completed, USB

driver Install window appears. Click “Yes”

button after taking out USB cable.

7. Click “Next” button.

8. Click “Finish” button to complete installation

and re-boot the computer.

Summary of Contents for R&D MAGIC-70

































































































































Search results

Summary of Contents for R&D MAGIC-70

Reviews:

Related manuals for R&D MAGIC-70

Brands by name

Popular brands

REDT R&D MAGIC-70, Manual

Search results

Summary of Contents for R&D MAGIC-70

Reviews:

Related manuals for R&D MAGIC-70

Brands by name

Popular brands