REDONDO RS User Manual Download

Page: 48 / 52

SPECIFICATIONS

Tuning Range (USA, EUR, AUS, JAP, RUS tuning capable) with RDS

87.5-107.9MHz

Antenna Terminal

External Antenna Connector

Usable Sensitivity

12.5 dBf

Selectivity

75 dB @ 400kHz

Signal to Noise Ratio

62 dB (stereo), 67 dB (mono)

Harmonic Distortion @ 1 kHz

0.8% (stereo), 0.5% (mono)

Separation

32 dB @ 1kHz

Frequency Response

30-16,000 Hz

Tuning Range (USA, EUR, AUS, JAP, RUS tuning capable)

530-1710 kHz

Antenna Terminal

External Antenna Connector

General

Dimensions (display face)

3.5” W x 1” H x 2.5” (with mounts) D

Dimensions (push-buttons)

3.5” W x .5” H

Dimensions (radio body)

3.96” W x 1.98” H x 4.30” D

Power Requirements

10.5-14.4 volts

Current Consumption (during operation)

Max. 15A

Current Consumption (car off)

<3.5 mA

Output Power (@ 14.4 volts @ 4 ohm @ 1% THD)

25x4 watts RMS / 45x4 watts Max Power

Output Impedance

4ohm

Low Level Output (4 channels)

2.85 volts

AUX 1 Input

>300 mV / 6 kΩ

AUX 2 Input

>300 mV / 6 kΩ

USB 1 Input

5V (USB female input)

USB 2 Input

5V (USB female input)

NOTE: All specifications are subject to change without notice.

Summary of Contents for RS





















































Search results

Summary of Contents for RS

Reviews:

Related manuals for RS

Brands by name

Popular brands

REDONDO RS, User Manual

Search results

Summary of Contents for RS

Reviews:

Related manuals for RS

Brands by name

Popular brands