RC WARBIRDS MiG-29 Retract Kit Manual Download | Manualshive

Page: 7 / 16

background image

JOINTLY DEVELOPED WITH
WWW.RC-WARBIRDS.COM

Page 7/16

Step 2: Main retract preparation

Each main retract former consists out of the
parts shown above. Before you begin
please read through this section and dry fit
all components.
NOTE: ensure that you build one right and
one left side retract mount.

Slot the 4x 3mm ply wood parts together as
shown above and glue with 30min epoxy.
Notice the difference between the 2 main
formers

Install the 4mm retract mounting plates as
shown above and glue with 30min epoxy
(apply the 30min epoxy to all areas that
have contact with the mounting plates).

Repeat the steps above for the 2

nd

retract

mount.
IMPORANT: Ensure to build one left and
one right hand side retract mount.

«
...
5
6
7
8
9
...
»

Summary of Contents for MiG-29 Retract Kit

















Reviews:

No comments

Related manuals for MiG-29 Retract Kit

Brand: Jet Hangar Pages: 2

P-47 Thunderbolt

Brand: J. Perkins Pages: 16

Brand: J-Power Pages: 32

Brand: N-Tech Jets Pages: 10

SPINNER MISSILE XL

Brand: Rage Pages: 2

Brand: THUNDER TIGER Pages: 28

Brand: Buki Pages: 12

Chatter Telephone HGJ69

Brand: Fisher-Price Pages: 12

Brand: Fisher-Price Pages: 2

Lokpuffer Puff-H0

Brand: Fichtelbahn Pages: 2

Corvus Racer 540 120CC

Brand: Goldwing RC Pages: 60

Brand: Smoby Pages: 2

LITTLE Chef DELUXE 200362

Brand: Smyths Toys Pages: 4

Sit-to-Stand Learning Walker

Brand: VTech Pages: 16

Lava Launch Coaster 50050

Brand: K'Nex Pages: 72

60ft Madison passenger cars

Brand: M.T.H. Pages: 8

Wattage Thermalaire EP

Brand: Academy of Model Aeronautics Pages: 28

Brand: Jamara Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands