RC WARBIRDS MiG-29 Retract Kit Manual Download | Manualshive

Page: 12 / 16

background image

JOINTLY DEVELOPED WITH
WWW.RC-WARBIRDS.COM

Page 12/16

Before the nose retract mount can be glued it is required to roughen the surface of the
fuselage on to which the formers are glued. Trial fit the nose retract mount and sand the
areas with 180-220 sand paper.
Once done glue the former in place with 30min epoxy and milled fiberglass.

NOTE:

Ensure that no glue touches the pull-pull cable or runs into the airtube.

Use a spanner to hold the mount in place until the epoxy has cured.

«
...
10
11
12
13
14
...
»

Summary of Contents for MiG-29 Retract Kit

















Reviews:

No comments

Related manuals for MiG-29 Retract Kit

Brand: Walachia Pages: 3

Baby Annabell 794982

Brand: Zapf Creation Pages: 2

Brand: Zapf Creation Pages: 24

Brand: AeroWorks Pages: 17

THE GHOST HOUSE

Brand: RavensBlight Pages: 10

Brand: Jamara Pages: 8

Brand: BLOTZ Pages: 2

Brand: Walkera Pages: 2

Jones & Laughlin Steel Slag Train

Brand: Lionel Pages: 12

Brand: PIKO Pages: 7

SPEED MASTER TG511

Brand: THINK GIZMOS Pages: 6

Baby Annabell 707210

Brand: Zapf Creation Pages: 54

Brand: Fisher-Price Pages: 8

Brand: Billing Boats Pages: 32

Jimu Robot JR1601

Brand: UBTECH Pages: 5

Brand: Chad Valley Pages: 7

Brand: Trix Pages: 24

Brand: Trix Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands