RC WARBIRDS MiG-29 Retract Kit Manual Download Page 8 | Manualshive

Page: 8 / 16

background image

JOINTLY DEVELOPED WITH
WWW.RC-WARBIRDS.COM

Page 8/16

Once all parts are dry, fit the retract unit
and mark the position of the mounting
holes. Ensure that the retract cylinder
points towards the former with the wire cut
out as shown above.

Drill the retract mounting holes (2mm drill)
and secure the retract unit in place.
Remove the retract unit. The main retract
mounting plates are now ready for
installation in the fuselage.

«
...
6
7
8
9
10
...
»

Summary of Contents for MiG-29 Retract Kit

















Reviews:

No comments

Related manuals for MiG-29 Retract Kit

Brand: Old School Model Works Pages: 14

Brand: LAEGENDARY Pages: 32

Brand: Bell Pages: 220

Brand: Bachmann Pages: 2

Brand: Faller Pages: 4

Brand: E sky Pages: 64

Spirit GPMA0530

Brand: GREAT PLANES Pages: 40

Maker ROK Robotics

Brand: Rokenbok Pages: 4

Brand: marklin Pages: 40

Brand: Faller Pages: 4

Brand: Raptor Pages: 41

LittlePeople Motorized Big Top Train 77706

Brand: Fisher-Price Pages: 6

Traffic Signal Bridge

Brand: VTech Pages: 10

Play & Move Puppy Tunes

Brand: VTech Pages: 11

Pitts Special S-2C 40

Brand: Kyosho Pages: 18

Marble Run Dragon

Brand: iDventure Pages: 56

HUZZLE Cast Hourglass

Brand: Hanayama Pages: 5

Berkshire LionChief

Brand: Lionel Pages: 36

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands