manualshive.com logo in svg

RaycoWylie i4500, Calibration Instructions Manual

Share
Download
RaycoWylie i4500 Calibration Instructions Manual Download Page 5

55M4500CCE00 REV A 

 

 

 

 
 
 

 

TABLE OF CONTENTS 

1 

INTRODUCTION ....................................................................................................... 7 

  Personnel qualification and scope of this manual ...................................................... 7 

  Using this manual ............................................................................................................ 7 

2 

CONFIGURATION .................................................................................................... 9 

  Step #1:  Accessing the calibration menu .................................................................... 9 

 

Step #2:  “Enable/Disable i/o” Setting ......................................................................... 10 

 

Step #3:  “Calibration units” setting ............................................................................ 12 

 

Step #4:  “Calibration data” Entry ................................................................................ 13 

 

Step #5:  “Dimensions” Data entry .............................................................................. 15 

 

Step #6:  “block capacities and block weights” setting ........................................... 18 

 

Step #7:  “system options” setting .............................................................................. 19 

 

Step #8:  “crane type”.................................................................................................... 20 

  Step #9:  

“bridging/bypass output” ............................................................................. 20 

 

Step #10:  “picture” ........................................................................................................ 20 

3 

CALIBRATION ........................................................................................................ 21 

 

Step #11:  “Zero sensor/Side of boom angle” angle  sensor calibration ................ 21 

 

Step #12:  “Zero sensor/Span sensor” length sensor calibration........................... 22 

 

Step #13:  “Zero pressure/Span pressure” sensor calibration ................................ 24 

 

Step #14:  “select boom output sequence” ................................................................ 26 

 

Step #15:  “No Load calibration”.................................................................................. 27 

 

Step #16:  “Loaded boom deflection” ......................................................................... 34 

  Step #17:  Optional 

“Load adjustment” ...................................................................... 36 

  Step #18:  Optional 

“Load offset” ................................................................................ 37 

  Step #19:  Optional 

“Load correction” ........................................................................ 39 

  Step #20:  

“Friction compensation” ............................................................................ 43 

 

Step #21:  “Transfer” Calibration backup ................................................................... 43 

 

“Transfer” restoring calibration and load chart files ................................................ 45 

 

“Memory” ........................................................................................................................ 46 

4 

OPTIONS ................................................................................................................. 47 

 

“Limits setting” parameters.......................................................................................... 47 

Summary of Contents for i4500



















































Reviews:

No comments

Brands by name

Popular brands

Load more brands