Raven SC1 Calibration & Operation Manual Download Page 22

Page: 22 / 88

CHAPTER 3

Raven SC1™/TC1™ (software version 1.5) Calibration & Operation Manual for Tractors and Sprayers

FIGURE 15. Terrain Comp Calibration Screen

8. Select the

Calibrate

button again to complete the Terrain Compensation Calibration.

9. Select the

Next

arrow.

NOTE:

If calibrating the SC1/TC1 system for GPS only operation, the Calibration Wizard Summary will be

displayed. Touch the Accept button to go to the GPS Only Home screen. Refer to Chapter 4,

Routine

Machine Operation

, for assistance with operating the SC1/TC1 system in GPS only mode.

If calibrating the auto-steering features, continue to the next section to continue the SC1/TC1 system

calibration.

FIGURE 16. Calibration Summary

AUTO-STEERING CALIBRATION

The Auto-Steering calibration consists of the following component setup calibrations:
•

Resume and Disengage Switch Calibration

•

Wheel Angle Sensor (WAS) Calibration

Summary of Contents for SC1
























































































Search results

Summary of Contents for SC1

Reviews:

Brands by name

Popular brands

Raven SC1, Calibration & Operation Manual

Search results

Summary of Contents for SC1

Reviews:

Brands by name

Popular brands