manualshive.com logo in svg

Raven SC1, Calibration & Operation Manual

Share
Download
Raven SC1 Calibration & Operation Manual Download Page 10

CHAPTER 2

6

Raven SC1™/TC1™ (software version 1.5) Calibration & Operation Manual for Towed Implements

INSTALLATION

RECOMMENDATIONS

Raven Industries recommends the following best practices when installing or operating the SC1/TC1 system for the 

first time, at the start of the season, or when moving the SC1/TC1 system to another machine:
• Verify that the machine hydraulic system is using fresh oil and that the filters have been recently changed.
• Ensure there are no issues with the machine hydraulic system (e.g., pump issues, faulty hydraulic motors, fine 

metal deposits in the hydraulic hoses, etc.).

 

WARNING

Carefully read and follow all safety requirements 

and precautions contained in this manual and the 

machine-specific or implement Installation 

Manual. Failure to follow safety instructions may 

lead to equipment damage, personal injury, or 

death.

Summary of Contents for SC1

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands