background image

 

 

-

 

Do not install on water that is microbiologically unsafe without adequate disinfection before or after the unit. For 
effective disinfection install a Rainfresh Drinking Water System or Rainfresh UV disinfection system.

 

-

 

For use on cold water only. 

 

-

 

Only use thread seal tape 

(Teflon® tape)

 

for fitting connections into unit. 

DO NOT USE pipe dope or chemical 

sealants. 

 

-

 

If water pipes are used to ground electrical system, install jumper wire

 

(#4 gauge solid copper wire) across the unit 

to maintain proper grounding of your electrical system 

-

 

Protect your unit from freezing 

- drain the unit if freezing temperatures exist.

 

-

 

NOTE: IF SOLDER TYPE FITTINGS ARE USED DO NOT USE torch near inlet/outlet connections. 

All solder joints 

should be made before joining pipe to filter head. Use only lead-free solder and flux. 

-

 

DO NOT over-tighten 

metal fittings on to unit connections.  

-

 

You will need softener salt with this unit (not included). Softener salt is sold at most retailers. 

-

 

Place the unit on a flat level surface. Do not place shims under the unit to level it. The weight of the unit full of 
water and salt can cause the softener tank to crack at the shim. 

-

 

The unit should only be moved by 2 or more people due to heavy weight. Failure to do so can result in back or other 
injury. 

-

 

The unit must be installed in an area where there is reasonable access to the salt tank for regular salt filling. 

 
INSTALLATION 

Electrical Requirements: 

 

The automatic control valve requires a constant power supply - 110V AC. We recommend a GFI (ground fault 
interrupter) outlet within 5 feet of the softener. Extension cords are not recommended.  

 

If water pipes are used to ground electrical system, you will need to install a jumper wire across the filter unit. 

 

Unpacking the unit 

The unit includes:  
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Unpack the unit and place it at the location where you intend to install it. 

 

Stand back and look at the softener to make sure it is standing straight up and not 
tilted to one side. Make sure your chosen location will be fairly level, dry, and 
protected from possible freezing conditions. The softener can sit directly on the floor 
and will not corrode. DO NOT set the softener onto make shift platforms as this can 
damage the salt tank, or may cause it to topple.  

 

The system has 3 connections - an inlet, an outlet, and a drain line connection. If you 
are looking at the back of the unit (

fig 1

), the inlet is on the left side. 

Warning: 

Make 

sure that you have correctly identified the inlet of the system. REVERSING THE 

WATER 

IN 

WATER 

OUT 

1)

 

Softener tank 
with control 
valve and bypass 
valve & brine 
(salt)  tank 

 

2)

 

Inlet/outlet elbow fittings (2) 
– ¾” Male NPT 

 

3)

 

Allen key (for ease of opening 
& closing bypass valve) 

 

5)

 

Drain hose (15 ft) with hose 
clamp 

 

4)

 

Brine overflow fitting 

 

6)

 

AC power adapter 

 

Fig 1 

Summary of Contents for 30TFM

















Reviews: