background image

 

 

12

 

  

Salt Setting (lbs/cu ft) 

Model 

6.0 

8.0 

10.0 

12.0 

15.0 

30TFM 

2.9 

3.8 

4.8 

5.7 

7.1 

45TFM 

4.2 

5.7 

7.1 

8.5 

10.7 

60TFM 

5.7 

7.6 

9.6 

11.4 

14.2 

 

Table 1 : Refill time (in minutes) for various salt settings using Sodium Chloride 

 
Disinfecting the Softener 

It  is  possible  that  during  shipping,  storage  &  installing,  bacteria  can  go  into  the  unit. 
Therefore, as a good installation practice, it is recommended that the softener be disinfected 
prior  to  use.  To  disinfect,  open  the  lid  of  the  brine  well  in  the  salt  tank  and  add  approx.  3 
tablespoons of fresh common household bleach. Replace lid & proceed to next step. 

 
Manual Regeneration 

If screen is locked, press “

 MENU” for 3 seconds to unlock. 

 To initiate an immediate regeneration, press the 

SET/REGEN

 

button for 3 seconds, an option for “

Delayed

” or “

Immediate

” regeneration will appear. Press the 

SET/REGEN

 button 

again  and  “

Delayed

”  will  begin  flashing.  Now  press  the  down  arrow  button  and  “

Immediate

”  will  flash.  Press  the 

SET/REGEN

 button once and then press the menu button once. Valve will immediately start manual regeneration.  

YOUR UNIT IS NOW READY FOR SERVICE 

 
 
OTHER FEATURES 

Control Operation During a Power Failure  

In the event of a power failure, the valve will keep track of the time and day for 48 hours.  The programmed settings 
are  stored  in  a  non-volatile  memory  and  will  not  be  lost  during  a  power  failure.    If  power  fails  while  the  unit  is  in 
regeneration, the valve will finish regeneration after power is restored.  If the valve misses a scheduled regeneration 
due to a power failure, it will queue regeneration at the next regeneration time once power is restored. 
 

Safety Float 

The  brine  tank  is  equipped  with  a  safety  float  which  prevents  your  brine  tank  from  overfilling  as  a  result  of  a 
malfunction such as a power failure. 

 

New Sounds 

You  may  notice  new  sounds  as  your  water  softener  operates.  The  regeneration  cycle  lasts  approximately  2  hours. 
During this time, you may hear water running intermittently to the drain. 

 

Manual Bypass 

In  the  case  of  emergency,  such  as  an  overflowing  brine  tank,  you  can  isolate  your  water  softener  from  the  water 
supply using the bypass valve located at the back of the control. To resume soft water service, open bypass valve by 
rotating the knobs counterclockwise. 

 

12  Backwash 

05 

 

 

 

Increase to 10 if water has lot of dirt 
or rust 

13  Brine / Rinse 

50 

 

 

 

Increase to 60 if water is more than 
15 grains hard 

14  Rapid Rinse 

 

 

 

Increase to 10  if you want a longer 
rinse time after regeneration 

15  Refill 

For REFILL settings based on your chosen salt settings, please refer to 

Table 1 

below 

16  Restore Default 

NO 

 

 

 

Leave at default. Change only if you 
would like to re-start programming 
from the beginning 

Open this lid & 
pour bleach inside 

Summary of Contents for 30TFM

















Reviews: