background image

1.6. Specifications

Size

174*86*157.5mm

Weight

355g

No battery

Frequency

2.400GHZ-2.480GHZ

Transmitting power

Module dependant

���

Antenna gain

2db

Battery

3.7V 18350 Lithium Ion

Charge port

USB-TypeC

Operation voltage

DC 6.6-8.4v

Range

> 2km @ 20dbm

Firmware

EdgeTX

Transmitter)

Channels

Up to 16 (Rx dependent)

Display

128*64 Monochrome LCD display

Gimbals

High precision potentiometer/ Hall-effect sensor (Package dependent)

External module

8Pin Nano Port

Upgrade method

USB/SD card & EdgeTX Companion PC software

1.7. Warranty and repair

Should any issues arise with your radio system's hardware, please keep the proof of purchase

and contact the retailer where you made the ZORRO purchase. . You may also visit our warranty

support page

https://www.radiomasterrc.com/contact

The limited warranty covers defects in workmanship for one year from the date of purchase

1.8. Disclaimer

OpenTX/EdgeTX are open source firmware. No warranty or implied warranty is given for the

quality and reliability of this firmware. If not handled properly, the RC model can cause serious

injury or even death. If you decide to use OpenTX/EdgeTX firmware, you are solely responsible

for your model. Any injury or damage caused by using OpenTX/EdgeTX firmware The authors of

OpenTX/EdgeTX and RadioMaster assume no responsibility. Use with caution.

Summary of Contents for Zorro








































Reviews: