RadioMaster Zorro Instruction Manual Download

Page: 2 / 39

Content

.......................................................................................................................................

1.1. Introduction

...............................................................................................................

1.2. Safety information

.....................................................................................................

1.3. Radio overview

...........................................................................................................

1.4. Battery and charging information

..............................................................................

1.5. Manual and firmware download

...............................................................................

1.6. Specifications

.............................................................................................................

1.7. Warranty and repair

...................................................................................................

1.8. Disclaimer

...................................................................................................................

1.9. Legal status and copyright

.........................................................................................

2. First boot

.....................................................................................................................................

2.1. Calibrating Gimbals

..................................................................................................

2.2. Set the default Gimbal mode and the default channel

..........................................

output order.

...................................................................................................................

3.Radio menu

..................................................................................................................................

3.1. Main interface

..........................................................................................................

3.1.1. Reset, Statistics and About

...........................................................................

3.2. System settings

........................................................................................................

3.2.1 TOOLS

.............................................................................................................

3.2.2 SD CARD

.........................................................................................................

3.2.3 RADIO SETUP

..................................................................................................

3.2.4 GLOBA FUNCTIONS

........................................................................................

3.2.5 TRAINER

.........................................................................................................

3.2.6 HARDWARE

....................................................................................................

3.2.7 VERSION

.........................................................................................................

3.3. Model selection

........................................................................................................

Summary of Contents for Zorro








































Search results

Summary of Contents for Zorro

Reviews:

Related manuals for Zorro

Brands by name

Popular brands

RadioMaster Zorro, Instruction Manual

Search results

Summary of Contents for Zorro

Reviews:

Related manuals for Zorro

Brands by name

Popular brands