RadioMaster Zorro Instruction Manual Download Page 7 | Manualshive

Page: 7 / 39

background image

1.4. Battery and charging information

ZORRO is powered by 2x 3.7V 18350 Lithium Ion cells and is charged using the built-in USB-C

port. The charging circuitry is designed for charging 2x 3.7V Lithium Ion/Poly or 1x 7.4V Lipo

battery pack only; the nominal voltage is 3.7V and the maximum charging voltage is 4.2V.

Never charge 3.6V LiFe and 3.6V 18350 Lithium Ion packs with the onboard charger. Charging or

using the wrong battery chemistry/polarity may cause permanent damage to the PCB and in

certain situations cause fires.

Check the voltage and condition of the battery regularly and never charge the device

unattended. Only charge in safe areas away from combustable materials. Refrain from charging

the radio unit if it was exposed to water or was damaged in any way. RadioMaster does not

assume any responsibility for any adverse consequences caused by the use or misuse of this

product.

1.5. Manual and firmware download

ZORRO is pre-installed with factory approved EdgeTX firmware and is also capable of operating

OpenTX. To download the latest manual or stock factory firmware, please visit the RadioMaster

website:

https://www.radiomasterrc.com

When updating your radios firmware we would encourage you to use EdgeTX Buddy.

EdgeTX

http://edgetx.org/

(Information about EdgeTX)

https://buddy.edgetx.org/

(easy to use tool for FW updates)

OpenTX

https://www.open-tx.org/

(Information as OpenTX)

«
...
5
6
7
8
9
...
»

Summary of Contents for Zorro








































Reviews:

No comments

Related manuals for Zorro

Brand: Denon Pages: 142

Brand: R&S Pages: 220

Brand: Samsung Pages: 94

L-1DVI-FE-TX/RX

Brand: Questtel Pages: 4

Brand: Ranger Pages: 18

XDOM RPL - PRODUCTSHEET

Brand: Ebode Pages: 24

Brand: GBD Pages: 4

Brand: ZoneVu Pages: 33

SD 236BT/RDS/USB/AX

Brand: Majestic Pages: 6

Brand: Galaxy Pages: 10

Brand: ZGEMMA Pages: 33

Brand: Brite View Pages: 30

MICRO LINK 490-30

Brand: Xantech Pages: 3

Brand: Yaesu Pages: 3

Brand: Radial Engineering Pages: 12

Brand: Sommerkamp Pages: 25

Brand: Yupiteru Pages: 20

Brand: JVC Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands