RadioMaster TX16S User Manual Download Page 2

Page: 2 / 59

Table of Contents

.............................................................................................................................................4

1.1. Introduction

..........................................................................................................................4

1.2. Safety instructions

.............................................................................................................. 4

1.3. Manual and Firmware Download

....................................................................................5

1.4. Important note on firmware.

........................................................................................... 5

1.5. Remote Control Overview

................................................................................................ 5

1.6. Important note on Power and charging precautions.

.............................................. 6

1.7. Note about this guide.

.......................................................................................................6

1.8. Specifications

....................................................................................................................... 7

1.9. Warranty and Repair

...........................................................................................................7

1.10. Firmware Update and OpenTX Information

..............................................................8

1.11. Disclaimer

............................................................................................................................8

1.12. Legal status and copyright

.............................................................................................8

2. OpenTX Companion software (OpenTX companion)

............................................................ 9

2.1. Software Download and Installation

............................................................................. 9

2.2. Use Companion software to upgrade remote controller firmware

.....................12

3. First boot

.......................................................................................................................................... 16

3.1. Calibrate the battery voltage

.........................................................................................18

3.2. Calibrating Gimbals

.......................................................................................................... 20

3.3. Set the default Gimbal mode and the default channel output order.

................23

4. Remote control menu details

..................................................................................................... 24

4.1. Main interface

.................................................................................................................... 24

4.2. System settings

..................................................................................................................24

4.2.1 TOOLS (Tool page) description

..........................................................................25

4.2.2 SD CARD (SD Card Page) Instructions

.............................................................25

4.2.3 RADIO SETUP Instructions

..................................................................................26

4.2.4 GLOBAL FUNCTIONS (Global Functions Page) Instructions

......................27

4.2.5 TRAINER (coach function page) description

................................................. 27

4.2.6 HARDWARE (Hardware setting page) Description

...................................... 28

4.2.7 VERSION (Version page) description

...............................................................29

4.3. Model selection

................................................................................................................. 29

Summary of Contents for TX16S




























































Search results

Summary of Contents for TX16S

Reviews:

RadioMaster TX16S, User Manual, Page: 2 / 59

Search results

Summary of Contents for TX16S

Reviews: