RadioMaster TX16S User Manual Download Page 7 | Manualshive

Page: 7 / 59

RadioMaster TX16S User Manual Download Page 7

7

1.8. Specifications

Specifications: 183 * 212 * 66 mm
Weight: 736g (excluding battery)
Transmission frequency: 2.400GHZ-2.480GHZ
Transmitter module: Internal Four-in-one multi-protocol RF module
Transmit power: maximum 22dbm (transmit power adjustable)
Working current: 400mah
Working voltage: 7-8.4v DC
Remote control distance:> 2km @ 22dbm
Open source firmware: OpenTX (remote control) DIY-Multiprotocol-TX-Module

(Internal RF Firmware driven by OpenTX)

Number of channels: Up to 16 channels (depending on the receiver)
Display: 4.3-inch TFT full-color display
Gimbals: Non-contact 3D Vector Hall Gimbal

JR / FrSKY Compatible Module Bracket

Upgrade method: Support USB online / SD card offline upgrade
Protocol: Full series DSM2 / X full series Flysky and Flysky 2A FrSKY and many

more.

For a complete list of agreements, visit:

https://github.com/pascallanger/DIY-Multiprotocol-TX-Module/blob/master/Protocols_Details.md

1.9. Warranty and Repair

If you experiance any problems with your remote control hardware, please keep

proof of purchase and contact the retailer where you purchased TX16s.

«
...
5
6
7
8
9
...
»

Summary of Contents for TX16S




























































Reviews:

No comments