manualshive.com logo in svg

RadioMaster TX16S, User Manual, Page: 6 / 59

Share
Download
RadioMaster TX16S User Manual Download Page 6

6

1.6. Important note on Power and charging precautions.

The TX16S has built-in USB charging function for 2cell 7.4v

Battery packs (2 x 3.7v Lithium cell packs). The charging

circuit is only suitable for 2x 3.7v lithium-ion 18650, 2 x

21700 3.7v lithium-ion (21700 2s 7.4v Lithium-Ion pack) or

2x 3.7v Lipoly batteries (2s 7.4v Lipo battery pack). The

nominal battery voltage per cell is 3.7v and the maximum

charging cut off voltage is 4.2v per cell.

Approved for use

2 x 3.7v Li-ION 18650 cells (7.4v using supplied tray)

2 x 3.7v Li-ION 21700 cells (Assembled as 7.4v 2s Battery pack)

2 x 3.7v Lithium-polymere cells (Assembled as 7.4v 2s Battery pack)

DO NOT use

3.6v Li-ION cells

2S 6.6v LiFE Battery packs

LiFEP04 cells

WARNING!

Do not use 2s 6.6v LiFE battery pack, 18650 lithium-ion cells

with a nominal voltage of 3.6v or LiFEP04 18650 Round cells.

Using the built in USB charger with incorrect battery types and

voltage may cause damage to the remote control or fire.

Check the health and condition of the batteries regularly. Do not use damged cells.

Never charge your device unattended. Always charge in a safe area away from

flammable materials. If the remote control gets wet or damaged in any way, do not

charge it.
RadioMaster is not responsible for any adverse consequences caused by using or

misusing this device.

1.7. Note about this guide.

This guide covers basic information about your radio. OpenTX software is very

powerful and has a large number of programming and mixing functions. Please visit

the site beloew for a comprehensive software installation guide for more detailed

instructions

https://www.open-tx.org

Summary of Contents for TX16S




























































Reviews:

No comments