manualshive.com logo in svg

RadioMaster TX16S, User Manual, Page: 59 / 59

Share
Download
RadioMaster TX16S User Manual Download Page 59

59

______________________________________________________________________

EU Simple Declaration of Conformity

RadioMaster declares the radio equipment TX16s is in compliance with EU

directives Directive 2014/53/EU. Full text of the declaration of conformity is
available at the following website

www.radiomasterrc.com

Manufacturer by

ShenZhen RadioMaster Co., Ltd

5th Floor, Yutian Building, No. 18 Yangtian Road, Xin’an Street, Baoan District,

Shenzhen, Guangdong.

______________________________________________________________________

FCC ID: 2AV3G-TX16S

FCC Information

This equipment has been tested and found to comply with the limits for Part 15 of

the FCC rules. This device complies with part 15 of the FCC rules. Operation is

subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Full text of the declaration of
conformity is available at the following website

www.radiomasterrc.com

CAUTION:

Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. This product

contains a radio transmitter with wireless technology which has been tested and

found to be compliant with the applicable regulations governing a radio

transmitter in the 2.400GHz to 2.4835GHz frequency range.

Antenna Separation Distance

When operating your RadioMaster transmitter, please be sure to maintain a

separation distance of at least 20 cm between your body (excluding fingers, hands,

wrists, ankles and feet) and the antenna to meet RF exposure safety requirements

as determined by FCC regulations.

Summary of Contents for TX16S




























































Reviews:

No comments